manualshive.com logo in svg

Ropex RESISTRON RES-408, Руководство по эксплуатации, Страница: 36 / 64

Поделиться
Скачать
Ropex RESISTRON RES-408 Скачать руководство пользователя страница 36

Controller functions

Page 36

RES-408

Version 1

11.5

Menu steps

Name

Description

Setting range

°C

Home position

The current actual value appears on the terminal 
display. The heatsealing band can be heated man-
ually (to the specified heatsealing or preheat tem-
perature) by pressing the "HAND" key.

HA

[

HA

nd]

Hand menu

The heatsealing band can be heated manually (to 
the specified heatsealing or preheat temperature) 
by pressing the "HAND" key.

This menu step is only available on con-
trollers 

manufactured 

up 

to

December 2000.

SH

[

S

eal

H

eat]

Heatsealing tem-
perature

The required heatsealing temperature (set point) 
can be set with the "UP" and "DOWN" keys.
Controllers manufactured up to May 2006:
The maximum selectable set point is limited by the 
controller version (300°C or 500°C).
Controllers manufactured as of June 2006:
The maximum selectable set point is limited by the 
rotary coding switch (alloy/range) and/or the PC vis-
ualization software.

Controllers manufactured 
up to May 2006:
0…300°C or 0…500°C

Controllers manufactured 
as of June 2006:
0, 40°C…maximum tem-
perature

PH

[

P

re

H

eat]

Preheat tempera-
ture

The required preheat temperature (PREHEAT) can 
be set with the "UP" and "DOWN" keys.
Controllers manufactured up to May 2006:
The preheat temperature must always be lower 
than the selected heatsealing temperature.
Controllers manufactured as of June 2006:
The maximum selectable preheat temperature is 
limited by the rotary coding switch (alloy/range) 
and/or the PC visualization software.

The preheat function can be deactivated by 
entering 0°C.

Controllers manufactured 
up to May 2006:
0°C…set point

Controllers manufactured 
as of June 2006:
0, 40°C…maximum tem-
perature

!

Содержание RESISTRON RES-408

































































Отзывы:

Нет отзывов