Ropex RESISTRON RES-408 Скачать руководство пользователя страница 1

Страница: 1 / 64

ROPEX Industrie-Elektronik GmbH

Tel.: +49 (0)7142-7776-0

E-Mail:

[email protected]

Adolf-Heim-Str. 4

Fax: +49 (0)7142-7776-211

Internet:

https://ropex.de

74321 Bietigheim-Bissingen (Germany)

Data subject to change

3.3.20

Version 1

RESISTRON

RES-408

Important features

• Microprocessor technology

• Separate terminal for operation and display

• Automatic zero calibration (AUTOCAL)

• Automatic optimization (AUTOTUNE)

• Automatic configuration of the secondary voltage and current ranges

(AUTORANGE, as of May 2006)

• Automatic phase angle compensation (AUTOCOMP, as of June 2006)

• Automatic frequency adjustment

• Wide current and voltage range

• 0…10VDC analog output for ACTUAL temperature

• 24VDC control signals for START and PREHEAT with electrical isolation

• Alarm function with fault diagnosis

• Heatsealing band alloy and temperature range selectable as standard (as of June 2006)

Operating

Instructions

Содержание RESISTRON RES-408

































































Результаты поиска

Содержание RESISTRON RES-408

Отзывы:

Ropex RESISTRON RES-408, Руководство по эксплуатации, Страница: 1 / 64

Результаты поиска

Содержание RESISTRON RES-408

Отзывы: