ROPA Tiger 5 Скачать руководство пользователя

Страница: 266 / 530

Operation

Strainer wheels (turbines)

266 / 530

6.17.2

Strainer wheels monitoring

The pressure of the hydraulic drive of the strainer wheels is constantly displayed on

the R-Touch in load monitoring. When exceeding a warning threshold (

) determined

by the driver (adjustable between 50% and 100% of drive pressure), the warning icon

flashes on the R-Touch. Simultaneously, a warning tone sounds. For setting the

warning threshold see page

127

Automatic speed adjustment

Automatic rotational speed adjustment increases the speed of the strainer wheels

when the bar graph of pressure indication (

) for the strainer wheels is 20% below

the warning threshold (

). Increasing of the rotation speed is visibly indicated in the

bar graph (

) for automatic rotation speed adjustment. Should the automated system

adjust the speed earlier, then only the warning threshold (

) is to be set to a lower

level. Should the speed adjustment come into effect later, then the warning threshold

(

) is to be set to a higher level.

ADVICE

If automatic speed adjustment should constantly indicate the maximum value, then a

higher cleaning stage must be selected or the lifting speed must be reduced.

(1)

Bar graph autom. rpm adjustment

(2)

Warning threshold

(3)

Bar graph strainer wheel drive pressure

Stone blockage detection

If a strainer wheel is abruptly blocked, all upstream drives and the driving power switch

off automatically. A warning indicating which strainer wheel is blocked appears on the

R-Touch.

. Simultaneously, a warning buzzer sounds.

This allows you to start searching for the problem directly on the affected strainer

wheel.

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

Результаты поиска

Содержание Tiger 5

Отзывы:

Похожие инструкции для Tiger 5

Бренды по названию

Популярные бренды