manualshive.com logo in svg

ROPA Tiger 5, Перевод оригинального руководства по эксплуатации

ROPA Tiger 5 - Эта мощная сельскохозяйственная машина требует регулярного обслуживания. Скачайте бесплатно переведенный оригинальный руководство по эксплуатации с manualshive.com, чтобы правильно ухаживать за вашим оборудованием. Подробное пошаговое руководство вам всегда под рукой.

Поделиться
Скачать
background image

Operation

Lifting

205 / 530

6.12

Lifting

6.12.1

Preparation for lifting

Familiarize yourself with the local ground and landscape before starting to work.
Get an overview of the field of beets to be lifted and determine the best place for set-

ting up the pile.
Instruct the people present before starting to work about the most important safety

regulations, especially the required safety distances. In any case, instruct all people

that you are obliged to immediately stop the machine and to immediately cease work if

any one enters the hazard zones.
– Switch to operating mode "Field".

– Swing out depth-control wheels.

– Swing down leaf sensor.

– Swing out leaf-spreader (only at PBS and PAS).

– Unfold bunker with the help of automatic folding.

6.12.2

Lifting process

– Drive into the field slowly and carefully so that the machine is in line with the row

counted.

– Preselect lifting through steer.

– Switch on machine drive.

– Set the min. and max. lifting speed (menu "Main settings", submenu "Others").

– Make the basic settings for the cleaning elements (infeed conveyor, strainer

wheels).

– Lower three-point suspension and drive into the field.

– Immediately adjust defoliator height and lifting depth to the situation. Ensure in

doing so that the beet leaf is topped a little above the beet crown and the sugar

beets are lifted from the ground completely.

– Check the setting of the scalper, in case of need, reset it.

– Check, by looking into the beet bunker, whether lifting is performed in the desired

quality. If not, immediately correct the corresponding settings.

– Check, by regularly looking into the lifting unit, whether the machine cleanly drives

within the row. If this is not the case, re-steer the rear axle so that the share bodies

are always in the centre of the possible shifting range, if possible.

Normally, first the headland is lifted and room for the pile created. Then, the field

is lifted through once to obtain enough manoeuvring space. The exact procedure

depends, as already mentioned several times, on the local conditions. In this case, the

expert knowledge and skills of the driver alone influence the lifting results.
During lifting, the sugar beets are stored in the bunker. Two ultrasound sensors in the

front bunker wall (1) and the rear bunker grid (1) detect the filling level of the bunker,

and in case of need, switch the rotating direction of the auger to fill up the bunker as

evenly as possible. When the bunker is filled up, the sugar beets must be unloaded

either onto a transport vehicle driving alongside, or deposited in a suitable place in the

form of a pile.

Содержание Tiger 5



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger 5

ABB Relion 670 series Communication Protocol Manual preview
Relion 670 series
Бренд: ABB Страницы: 66
Makita EN5550SH Parts Breakdown preview
EN5550SH
Бренд: Makita Страницы: 10
7th Sense medialon Showmaster Go User'S Reference Manual preview
medialon Showmaster Go
Бренд: 7th Sense Страницы: 9
Gardena 13137-20 Quick Start Manual preview
13137-20
Бренд: Gardena Страницы: 8
GARANT SG1 Operation Manual preview
SG1
Бренд: GARANT Страницы: 239
p-light Midi Installation And Instructions For Use preview
Midi
Бренд: p-light Страницы: 36
Garelick 19250 Installation Instructions preview
19250
Бренд: Garelick Страницы: 2
Garelick 74002 Assembly And Installation Instructions preview
74002
Бренд: Garelick Страницы: 2
Gardigo 60064 Instruction Manual preview
60064
Бренд: Gardigo Страницы: 32
Patiova Olympus Assembly Manual preview
Olympus
Бренд: Patiova Страницы: 19
Gatekeeper ITSS Installation Manual preview
ITSS
Бренд: Gatekeeper Страницы: 8
Gate Bure Rise & Go DB 56-309 Technical Manual preview
Bure Rise & Go DB 56-309
Бренд: Gate Страницы: 8
Latham 309 Installation Manual preview
309
Бренд: Latham Страницы: 4
SafeWaze LATITUDE Manual preview
LATITUDE
Бренд: SafeWaze Страницы: 23
York 1002 Assembly Instruction Manual preview
1002
Бренд: York Страницы: 26
Olympus EVIS EXERA III Instructions Manual preview
EVIS EXERA III
Бренд: Olympus Страницы: 130
Lumineux Eyebrook Installation Instructions preview
Eyebrook
Бренд: Lumineux Страницы: 2
PHAROS MARINE PHALCON 2000 Installation Manual preview
PHALCON 2000
Бренд: PHAROS MARINE Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды