manualshive.com logo in svg

Ronix 4645PRO, Руководство пользователя

Поделиться
Скачать
Ronix 4645PRO Скачать руководство пользователя страница 26

GASOLINE CHAIN SAW

25

WARNINNG! 

 

The spiked bumper must always be put on while using the chain saw on 
tree trunk. Push the spiked bumper into the tree trunk by using the rear 
handle. Push the front handle in the direction of cutting line. The spiked 
bumper must be remaining set for further saw guiding if necessary. Use 
a spiked bumper when cutting trees and thick branches can ensure your 
safety and decrease the working strength and vibration level.
If there’s barrier between the cutting material and chainsaw, turn off the 
machine. Wait until it stops completely. Wear the safety glove and remove 
the barrier. If the chain must be removed, please follow the instruction 
of relevant part like installation in manual. A trial run must be conducted 
after the cleaning and newly installation. If vibration or mechanical noise is 
discovered, please stop the use and contact your dealer.

MAINTENANCE

WARNINNG! 

  

Before cleaning, inspecting or repairing your unit, make sure that 
engine has stopped and is cool. Disconnect the spark plug to prevent 
accidental starting.
Follow the instructions to carry out regular maintenance, pre-operating 
procedures and daily maintenance routines. Improper maintenance may 
result in serious damage to the machine.

Содержание 4645PRO






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды