Ronix 4645PRO Скачать руководство пользователя | Manualshive

Страница: 13 / 37

background image

USER MANUAL

12

.

OPEN THE BOX AND INSTALL THE GUIDE BAR AND THE SAW

CHAIN ON THE POWER UNIT AS FOLLOWS.

WARNINNG!

11

12

13

The saw chain has very sharp edges. Use protective gloves for safety.
1) Pull the guard towards the front handle to check that the chain brake
is not on.
2) Loosen two nuts (13) and remove the chain cover (12) and spacer (11).
3) Gear the chain to the sprocket and, while fitting the saw chain around
the guide bar, mount the guide bar to the power unit. Fit the chain
tensioner nut (8) into the lower hole (7) of the guide bar, then install the
chain cover, and fasten the mounting nut to finger tightness. Make sure
the pin (9) on the clutch cover has inserted in the hole
(1) on the crankcase
(7) Hole
(8) Chain tensioner nut
(9) Clutch cover
(10) Hole
(11) Spacer
(12) Clutch cover
(13) Nuts

«
...
11
12
13
14
15
...
»

Содержание 4645PRO






































Отзывы:

Нет отзывов

Похожие инструкции для 4645PRO

Бренд: Kamikaze Страницы: 142

Бренд: Palmera Страницы: 25

Бренд: Stihl Страницы: 94

Бренд: GreenWorks Pro Страницы: 13

Бренд: Jonsered Страницы: 92

Бренд: Jonsered Страницы: 252

Бренд: CMi Страницы: 361

Бренд: Echo Страницы: 21

Бренд: Nakayama Страницы: 22

Бренд: RADLEY Страницы: 28

Бренд: Echo Страницы: 36

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 40

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 44

Бренд: Makita Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды