RONDELL RDE-1106, Руководство пользователя

Страница: 15 / 32

15
•
When the drink heats up to the required temperature, switch
the steam supply off by setting the control handle (3) to the
position «0».
•
Switch the coffee maker off by pressing the button (18) « ».
HEATING WATER
•
Make sure that there is enough water in the water tank (2),
and the steam supply handle (3) is set to the position «0»
and slightly tightened.
•
Place a suitable cup on the tray grid (8) and point the tip
(5) into it.
•
Press the power button (18), wait until the indicator light
stops flashing and starts to glow constantly.
•
Slowly turn the steam supply control handle (3) counter-
clockwise, and then press the manual water supply button
(21) «
», while the pump will turn on for 3 seconds, after a
pause the pump will turn on again, and hot water will be sup-
plied from the tip (5) constantly.
•
Switch the water supply off by pressing the button (21) « »
and turn the handle (3) clockwise until bumping.
Descaling (decalcination)
To increase the service life of the coffee maker, it is critically
important to perform timely descaling of the unit. The desca-
ling frequency depends on water hardness in your region. To
determine the level, we recommend using paper indicator tes-
ters that are immersed in water and change color depending
on the amount of calcium, magnesium and iron. Based on the
data obtained, it is necessary to choose one of the following
decalcination frequency schemes:
Level Water hardness, mg/l Descale after
(number of cups)
Level 1 0-50 880
Level 2 51-120 440
Level 3 151-250 280
Level 4 251-425 220
•
You can use calcium powder or tablets that are designed for
automatic coffee machines and other food and drink making
devices as a cleaning agent.
•
Prepare the descaling solution according to the instructions
on the cleaning agent.
•
Fill the water tank (2) with the prepared solution to the max-
imum mark and place it in the coffee maker.
•
Install the coffee filter (14 or 15) in the holder (12). Install
the filter holder (12) into the coffee maker. The holder (12)
ledges should match the groves on the boiler, after that turn
the filter holder (9) handle to the right until bumping.
•
Place a suitable cup on the tray grid (8).
•
Insert the power plug into the socket.
•
Turn on the coffee maker by pressing the button (18)
«
», you will hear a sound signal, and the white light indi-
cator will flash.
•
Wait until the light indicator glows constantly.
•
Press the manual water supply button (21) « » and fill a
cup with about 100 ml of water (this is necessary in order to
remove water from the boiler and fill it with a descaling solu-
tion), turn off the water supply by repeatedly pressing the
button (21) «
».
•
Remove the tip (5) from the cappuccinator pipe (4) and put
a suitable bowl under the pipe (4). Press the button (22)
«
» and wait for the boiler to heat up (the red light indicator
will glow constantly). Slowly turn the steam supply control
handle (3) and open the steam supply for 10-15 seconds.
Close the steam supply by setting the control handle (3) to
the position «0».
•
With small intervals, repeat the boiler cleaning procedure until
the descaling solution in the tank (2) is completely finished.
•
Fill the tank (2) with clean water and wash the boiler again
until the water in the tank (2) runs out.
•
Switch the coffee maker off by pressing the button (18) « ».
CLEANING
•
If during the filter (14/15) cleaning you find out that the open-
ings are blocked with the ground coffee remnants, you can
clean them with a small brush.
•
Clean the coffee maker body with a soft, slightly damp cloth
and then wipe it dry.
•
Do not use metal brushes or abrasives to clean the cof-
fee maker.
•
Do not immerse the power cord, the power plug and the cof-
fee maker body into water or other liquids.
•
Wash the removable parts of the coffee maker (2, 6, 8, 12,
14, 15, 16) with warm water and a neutral detergent, then
rinse them and dry.
Drip tray and grid
Remove the grid (8) from the tray, remove the tray (6) and pour
out water, wash the tray and put it back to its place, put the grid
(8) on the tray.