background image

Employ  the ESM-2 measuring device only for 
the measurements described in  these directi-
ons.  Contraventions  can  result  in  destruction 
of the measuring device.

Liability and guarantee

Every liability which arises from application of the device is excluded.

The guarantee period is  24  months  from  delivery  date. Within  this 
time,  all  deficiencies  which  cannot  be  attributed  to  inappropriate 
handling, will be repaired immediately and clear of all charges. In the 
case where a  repair  is  required,  please send the device to  us  with 
the proof of purchase.

Assistance and support 

Should you  require  assistance in  the application  of  the device, then 
you can  reach us under the Fax No.: 08282-7305  or  on Tel.: 08282-
7385 with operational questions about the device.

We wish  you a  lot of success with  the ESM-2 electro-stress measu-
ring device, so that you and your family can  again relax and live free 
of electro-stress.

Measurements  of  the  electromagnetic  contamination  of  apart-
ments,  offices and building  sites etc.  are carried out according 
to  the construction-biological  standard  by ROM Electronik  and 
construction  biologists,  who  possess  the  necessary  technical 
measurement equipment.

More Informations under http://bundesverband-elektrosmog.de
or 

www.rom-electronic.com

ROM-Elektronik GmbH

Am Grund 13

86489 Deisenhausen

Tel.: 08282-7385 Fax:08282-7305

Page 12

Содержание ESM-2













Отзывы: