RollSeal RS-500 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 44

RollSeal RS-500 Series Скачать руководство пользователя страница 33

Part No 4801-5158 Rev 1-2017

RS500/600 Series Doors

Page 33

Warning!

Dangerous High Voltages!

Allow Approximately 5 Minutes For The Controller To Power-Down

Before Changing Switch Settings, Jumper Placement, Or Wiring.

Warning!

Use The Correct RS Door Brake Rectifier For The Specific Required Voltage!

Using A 230 VAC Brake Rectifier With A 115 VAC Power Supply Can Result In

Improper Door Operation Due To The Mechanical Brake Not Releasing Properly.

Using A 115 VAC Brake Rectifier With A 230 VAC Power Supply Can Result In

Damage To The Mechanical Brake And/Or Brake Rectifier Resulting In Door Failure.

The SC-325/SC-650 Controllers and RS-500/600 Doors can be field upgraded to accommodate either 115
VAC or 230 VAC power supply. If the desired power supply voltage is different from the factory
preset/prewired voltage, the appropriate version Brake Rectifier must be ordered separately, field-installed on
the RS Door, and the SC Controller switch and jumper settings changed accordingly.

Note!

If Your Serial # Comes After

‘0010156’,

You May Have A Motor

That Requires The

Blue W/White Stripe Wire

To Be Changed

From T8 & T2

To Now Use T9 & T3 Instead.

The Blue W/Red Stripe

Now Uses T8 And T2.

!

!

!

!

«
...
31
32
33
34
35
...
»

Содержание RS-500 Series













































Отзывы:

Нет отзывов