43
Detailed Editing for a Patch (PATCH Parameters)
Parameter
Value
Explanation
DESTINATION 1–4
OFF, PITCH, CUTOFF,
RESONANCE, LEVEL,
PAN, OUTPUT LEVEL,
CHORUS SEND,
REVERB SEND,
LFO1/2 PCH DEPTH,
LFO1/2 TVF DEPTH,
LFO1/2 TVA DEPTH,
LFO1/2 PAN DEPTH,
LFO1/2 RATE,
PCH ENV A-TIME,
PCH ENV D-TIME,
PCH ENV R-TIME,
TVF ENV A-TIME,
TVF ENV D-TIME,
TVF ENV R-TIME,
TVA ENV A-TIME,
TVA ENV D-TIME,
TVA ENV R-TIME, TMT,
FXM DEPTH,
MFX-CTRL1–4
Tone parameters that are to be controlled when using the Matrix Control
Up to four parameters can be specified for each Matrix Control, and controlled
simultaneously.
* In this manual, parameters that can be controlled using the Matrix Control are marked with
a “
★
.”
SENS 1–4
-63–+63
Amount of the Matrix Control’s effect that is applied
• If you wish to modify the selected parameter in a positive (+) direction—i.e., a higher
value, toward the right, or faster etc.—from its current setting, select a positive (+) value.
• If you wish to modify the selected parameter in a negative (-) direction—i.e., a lower
value, toward the left, or slower etc.—from its current setting, select a negative (-) value.
• For either positive or negative settings, greater absolute values will allow greater amounts
of change. Set this to “0” if you don’t want to apply the effect.
TONE 1–4
(Tone Switch 1–4)
OFF, ON, REV
Tone to which the effect is applied when using the Matrix Control
OFF:
The effect will not be applied.
ON:
The effect will be applied.
REV:
The effect will be applied in reverse.
CONTROL SW
Parameter
Value
Explanation
RCV BENDER
(Receive Bender)
OFF, ON
For each tone, specify whether MIDI Pitch Bend messages will be received (ON), or not (OFF).
RCV EXP
(Receive Expression)
OFF, ON
For each tone, specify whether MIDI Expression messages will be received (ON), or not (OFF).
RCV HOLD-1
(Receive Hold-1)
OFF, ON
For each tone, specify whether MIDI Hold-1 messages will be received (ON), or not (OFF).
* If “NO-SUS” is selected for ENV MODE parameter, this setting will have no effect.
REDAMPER
OFF, ON
You can specify, on an individual tone basis, whether or not the sound will be held when a Hold
1 message is received after a key is released, but before the sound has decayed to silence.
If you want to sustain the sound, set this “ON.” This function is effective for piano sounds.
* In order to use this function, you must also set RCV HOLD-1 to “ON.”
RCV PAN MODE
(Receive Pan Mode)
CONTINUOUS,
KEY-ON
For each tone, specify how pan messages will be received.
CONTINUOUS:
Whenever Pan messages are received, the stereo position of the tone will be
changed.
KEY-ON:
The pan of the tone will be changed only when the next note is played. If a pan
message is received while a note is sounding, the panning will not change until the next key is
pressed.
* The channels cannot be set so as not to receive Pan messages.
ENV MODE
(Envelope Mode)
NO-SUS,
SUSTAIN
When a loop waveform (p. 24) is selected, the sound will normally continue as long as the key is
pressed. If you want the sound to decay naturally even if the key remains pressed, set this to “NO-
SUS.”
* If a one-shot type wave (p. 24) is selected, it will not sustain even if this parameter is set to
“SUSTAIN.”
