Rohde & Schwarz R&S SMA100A Скачать руководство пользователя страница 4

Страница: 4 / 33

R&S SMA100A

Information on the Current Version and History

Release Notes for Firmware 1171.5360.52

Information on the Current Version and

History

General information

This

document describes the procedure to apply a firmware update to the

R&S

SMA100A Signal Generator. It furthermore describes the differences between the

several firmware versions. The most current firmware version can be obtained from

www.rohde-schwarz.com

Instruments covered

This firmware version is suitable for all instruments of type

R&S

SMA100A,

including all module revisions, options and firmware licenses.

Identify current firmware version

The current instrument firmware revision is displayed during the startup sequence of
the instrument. In addition, it is provided in the

SETUP

Software/Options dialog and it is

part of the SCPI *IDN instrument identification string.

Potential malfunction of assembly!

It is strongly recommended to

do no firmware downgrade below

the version the

device was originally delivered with. Improved module revisions as well as modified
structure of calibration data may not be supported by previous firmware versions.

1.1 Special hints for particular instruments and

firmware versions

Instruments with serial number 112000 or higher

It is not possible to downgrade the firmware to version less than 3.01.102.11. After a
downgrade the

R&S® SMA100A does not work furthermore. The serial number of the

R&S® SMA100A could be obtained in the menu

SETUP

Hardware Config

.Please select

the entry SMA100A in the table Common Assembly.

Содержание R&S SMA100A


































Результаты поиска

Содержание R&S SMA100A

Отзывы:

Похожие инструкции для R&S SMA100A

Бренды по названию

Популярные бренды

Rohde & Schwarz R&S SMA100A, Руководство пользователя

Результаты поиска

Содержание R&S SMA100A

Отзывы:

Похожие инструкции для R&S SMA100A

Бренды по названию

Популярные бренды