Rohde & Schwarz 1402.9557.02 Скачать руководство пользователя страница 28

Страница: 28 / 80

DVB-H User Interface

DVB-H

Operating Manual 1008.0970.12 ─ 16

For details, refer to

chapter 2.2.3, "Forward Error Correction for Multiprotocol Encapsu-

lated Data (MPE-FEC)"

on page 17.

Remote command:

[:SOURce<hw>]:BB:DVB:DVBH|DVBT:TPS:MFEC[:STATe]

on page 74

TPS Table

The TPS parameter bit table displays the status of the transmitted TPS parameter bits.

Table 3-1: TPS signaling information transmitted in DVB-H

Bit number

Format

Purpose

0/1

Initialization bit for the differential 2-PSK modulation.
The modulation of the TPS initialization bit is derived
from the PRBS sequence

1-16

Bits 1 to 16 of the TPS are the synchronization words
for the TPS blocks in the super-frames:

0011010111101110

Synchronization word for the first and the third TPS
block in each super-frame

11001010000100001

Synchronization word for the second and the fourth
TPS block in each super-frame

17-22

The first 6 bits of the TPS information is used as a
TPS length indicator to signal the number of used bits
of the TPS:

010111

Cell Identification is not transmitted (23 TPS bits in
use)

011111

Cell Identification information is transmitted (31 TPS
bits in use)

100001

Cell Identification information is transmitted for DVB-H
(33 TPS bits in use)

23-24

Indicates the frame in the super-frame. Four frames
constitute a super-frame.

Frame 1 in the super-frame

TPS Settings

Содержание 1402.9557.02

















































































Результаты поиска

Содержание 1402.9557.02

Отзывы:

Похожие инструкции для 1402.9557.02

Бренды по названию

Популярные бренды

Rohde & Schwarz 1402.9557.02, Руководство по эксплуатации

Результаты поиска

Содержание 1402.9557.02

Отзывы:

Похожие инструкции для 1402.9557.02

Бренды по названию

Популярные бренды