Rogers PRT42, Инструкция по установке и программированию

Страница: 13 / 30

PRT42 and PRT42-BK v1.0 fv72 EN Rev.C
14
6 S
T A N D
-
A L O N E
O
P E R A T I O N
6.1 Users
In the stand-alone mode, a PRT reader can register up to 120 users, each with a card, a 3 to 6 digit long PIN
code and an ID number (000–119). The PRT reader precludes assignment of the same code or card to 2
different users. Users enter their PIN codes keyed in with a press of the [#] key ([#] key is required to mark
the end of PIN entry). User identification is done by verifying the PIN code entered or the card presented. When
an option [Card+PIN] set users must present his card and subsequently enter its PIN. The [Card+PIN] option
can be set separately for primary and secondary reader.
The PRT reader supports five types (classes) of users: INSTALLER, MASTER, NORMAL, TOGGLE and TOGGLE
LTD. The INSTALLER and MASTER Users are dedicated for programming purpose only. NORMAL Users are
authorized to unlock the supervised door, but not to arming and disarming reader. TOGGLE Users are
authorized both to unlock the system-supervised door and to switch reader between ARMED-DISARMED modes.
TOGGLE LTD Users are authorized to change ARMED-DISARMED mode of the reader only, they are not
authorized for door unlock.
A new user can be registered in the device following either a simple or a full programming procedure. The
simple procedure consists in programming a PIN code or a card into the system without specifying the ID
number of a user to whom the programmed PIN/card will belong — so the system simply stores the code
entered/card presented in a unoccupied ID user number. The full programming procedure requires you to
specify an ID number for the new user being programmed which has to be followed by entering his PIN code
and presenting his card.
Note: When you program user using full programming procedure you will be able later to selectively delete a
user simply by specifying his ID number, so you do not need to know his card or PIN code.
User Types (User Classes)
INSTALLER A card of this user allows you to enter Installer Programming Mode. INSTALLER
user has no PIN code.
MASTER A card of this user allows to enter User Programming Mode. MASTER user has no
PIN code.
NORMAL Users of this type are solely authorized to unlock the door. They can use a card
or a PIN code.
TOGGLE Users of this type have the authorization to unlock the door and to control the
ARMED-DISARMED state of the reader. They can use a card or a PIN code.
TOGGLE LTD Users of this type are solely authorized to control the ARMED-DISARMED state of
the reader. They can use a card or a PIN code.
6.2 ARMED and DISARMED Modes
In the standalone mode, the reader can be in any of the operational states, either ARMED or DISARMED. Its
current state is indicated by the reader’s dual color LED STATUS — it lights in RED for ARMED or GREEN for
DISARMED.
The change of the reader’s state to ARMED can be additionally indicated through the output line (for this,
enable the Reader Disarmed Output setting). Such configuration allows the output line to be used as a driver to
arm/disarm a connected alarm system or to switch on/off some other auxiliary system or device such as
heating, lights etc. In general, the reader’s ARMED-DISARMED states has no effect on unlocking door, unless
the Access Disabled When Reader Armed option has been enabled (see C13 digit in Installer Programming
Mode). With this option activated, access to the supervised room is granted only when the reader is disarmed.
Use of the reader’s configuration option mentioned above makes TOGGLE Users capable of enable/disable
access to the supervised room; and it allows automatic access locking upon a reader entering the ARMED state.
Note: Upon powering on, the reader automatically returns to the ARMED/DISARMED state it was in before
power off. Also, the reader restores its original ARMED/DISARMED state after exiting the programming mode.
After erasure of the reader’s memory the reader always returns to ARMED state
6.3 Arming and Disarming of Reader (rearming)
The action that changes the reader’s state from ARMED to DISARMED and vice versa will be referred to as
REARMING, the term “arming” should be understood as switching the reader into the ARMED state, and the
term “disarming” as switching the reader into the DISARMED state.