background image

MCX16-AP Operating manual.doc 

  

2018-11-29 

 

4/12 

 

output  polarity  is  done  within  low  level  configuration  using  RogerVDM  software.  By  default,  outputs  are 
configured with normal polarity. Outputs are assigned with functions using VISO management software. 

REL1 and REL2 outputs 

The expander offers two relay outputs REL1 and REL2. Each relay offers NO/NC terminals and is 30V/1.5A 
rated. In case of power outage both relays remain in the off state. Outputs are assigned with functions using 
VISO management software. 

AUX power output 

AUX  power  supply  output  is  dedicated  to  supply  additional  devices.  The  terminal  AUX+  is  protected  with 
1.0A electronic fuse. The terminal AUX- is internally shorted to ground. 

TML power output 

TML  power  supply  output  is  dedicated  to  supply  additional  devices.  The  terminal  TML+  is  protected  with 
0.2A electronic fuse. The terminal TML- is internally shorted to ground. 

Connection of expander to controller 

The expander is operated as an extension of MC16 access controller. After addressing in 100-115 range the 
expander  is  connected  to  RS485  communication  bus  of  controller  where  MCT  readers  and  other  MCX 
expanders are usually  also operated.  Any topology  of communication bus can be used  in RACS 5 system 
(e.g. star, tree) and the matching resistors (terminators) connected at the ends of transmitting lines are not 
required.  The  communication  works  with any  signal  cables  e.g.  U/UTP  cat.5. All  devices  connected  to the 
same bus should have GND terminals connected. The RS485 communication standard in RACS 5 system 
offers proper communication in a distance of up to 1200 meters as well as high resistance to interferences.  
It is recommended to supply the MCX16-AP from own transformer and equip it  with backup battery (fig.4). 
Alternatively  the  expander  can  be  supplied  from  AUX  output  of  MCX2D/MCX4D  expander  within  MC16-
PAC-2/3/4/-KIT  (fig.  5)  or  AUX  output  of  MC16  controller  supplied  from  18VAC  transformer  and  equipped 
with own battery (fig.6). 
 

 

Fig. 4 Connection diagram for expander with own supply (recommended) 
 

Содержание MCX16-AP













Отзывы: