EN
57
D
Door open indicator / photocell test function and “battery saving”
8LIMRHMGEXSVMWSJJ[LIRXLIHSSVMWGPSWIHERHWXIEHMP]PMXHYVMRKQERSIYZVIWERH[LIRXLIHSSVMW
open.
8LIMRHMGEXSVƽEWLIWWPS[P]HYVMRKSTIRMRKQERSIYZVIWERHMWPMXWXIEHMP][LIRXLIHSSVMWGSQ
TPIXIP]STIR-XƽEWLIWUYMGOP]HYVMRKGPSWMRKQERSIYZVIW
-JXLIHSSVMWWXSTTIHMRERMRXIVQIHMEXITSWMXMSRXLIPEQTI\XMRKYMWLIWX[MGIIZIV]WIGSRHW
Set
if the output
SC
MWYWIHJSVXLITLSXSGIPPXIWX7IIƼK
Set to
if the output
SC
MWYWIHJSVXLIƈFEXXIV]WEZMRKƉJYRGXMSR7IIƼK
;LIRXLIHSSVMWGSQTPIXIP]STIRSVGPSWIHXLIGSRXVSPPIVYRMXHIEGXMZEXIWER]EGGIWWSVMIWGSRRIGXIH
to terminal
SC
to reduce battery consumption.
Set to
if the output
SC
MWYWIHJSVXLIƈFEXXIV]WEZMRKƉJYRGXMSRERHTLSXSGIPPXIWXJYRGXMSR7IIƼK
Setting deceleration during opening
Setting deceleration during closing
01= the door decelerates near the limit switch
...
05= the door decelerates long before the limit switch.
Setting door closed position
The value set must ensure that the door is closed correctly after the limit switch is activated.
Warning!
)\GIWWMZIP]LMKLZEPYIWMQTIHISFWXEGPIHIXIGXMSR[MXLMRXLIƼREPGQSJHSSVXVEZIP)\GIW
sively low values cause the door to reverse (open) when it reaches the door closed stop.
Motor revolutions.
Setting pressure against door closed stop
N.B.
EWXLIHSSVETTVSEGLIWXLIHSSVGPSWIHWXSTSRGIXLIPMQMXW[MXGLMWEGXMZEXIHXLIGSRXVSPYRMX
reduces the torque applied by the motor to prevent the structure of the overhead door from bending
or straining.
Warning!
This parameter must be set in relation to the type of door installed and the mounting used
for the gear motor.
If this parameter is not set correctly, the automation system may not function properly and may
caused structural damages.
00= minimum force...09= maximum force.
Partial opening adjustment (%)
N.B.
8LMWTEVEQIXIVMWWIXXS LEPJSJXSXEPHSSVXVEZIPF]HIJEYPX
From 10% to 85% of total door travel.
Setting automatic closing time
8LIXMQIVWXEVXWJVSQXLIHSSVSTIRWXEXIERHGSRXMRYIWJSVXLIWIXXMQI3RGIXLIWIXXMQIMWVIEGLIH
the door closes automatically. The timer count restarts if a photocell is triggered.
Pause time settable from 00 to 90 s.
Pause time settable from 2 to 9 min.
Setting reverse time after activation of sensing edge or obstacle detection
(crush prevention)
This sets the reverse manoeuvre time after activation of the sensing edge or the obstacle detection
system.
From 0 to 30 s.
Enable electric lock
Disabled.
Enabled. The electric lock is activated for a period of 3 seconds 0.5 seconds before the start of the
QERSIYZVI;LIRXLIHSSVMWGPSWIXSXLIHSSVGPSWIHWXSTXLIGSRXVSPYRMXEWWMWXWVIIRKEKIQIRXSJ
the electric lock.
Содержание B70/2B
Страница 2: ...2 ...
