background image

Quick user guide

Helpy GSM

Issue 1.00

Page 6

Installation

Ensure that at the installation location a power plug in available nearby. For the wall 
installation you can use the screws delivered with the unit.
It is very important that the Helpy GSM unit has all time the best GSM signal to 
avoid disturbances during operation time. Before you install the device at his fi nal 
position be sure that it is the best spot you can fi nd. To do this use an mobile phone 
with a SIM card of the same provider that you are going to use with the Helpy GSM 
and try at the spot you are going to use to setup a communication. If during the 
conversation you will notice disturbances or interruptions you will have to look for a 
better position.

SIM card installation

For the installation of the SIM card be sure that the devices is 

SWITCHED OFF

! The 

SIM card has to be placed into the specifi c slot. The card should have the PIN code 
disabled.

PLEASE NOTE!
If you change the SIM card switch all time the POWER OFF!

Ensure that the PIN code of the SIM card is disabled with a mobile phone BE-
FORE you install it into the device.

If the SIM card is changed ensure that the new card has the PIN code is 
disabled. 

For a proper maintenance of the device you need a SIM card with SMS and 
GPRS data volume. SMS is required for programming and data volume for fi rm-
ware updates. For data connectivity ensure that you have the APN user name 
and password available from your provider.

GSM antenna

The antenna provided is connected to the device with the proper connector outside 
the case. If you notice problems in getting a proper GSM network signal you may 
change the antenna. Specifi c antennas may solve the problem. Ask the technical 
support for more informations,

PLEASE NOTE!
Never power the Helpy GSM WITHOUT connected antenna. The radio transmis-
sion engine may be damaged.

The device is designed for statical installation and external power supply with 230 
VAC. If required also a 12 VDC (min 11, max. 15 VDC) power voltage can be used. 
The device has an internal NiMH battery for emergency power supply if external 
power is missing.

Connection of the external power supply

Содержание HELPY GSM

































Отзывы: