manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, Руководство пользователя

Поделиться
Скачать
Rockwell Automation Allen-Bradley PowerFlex 4 Скачать руководство пользователя страница 84

C-2

RS485 (DSI) Protocol

Control Terminal 16 on the PowerFlex 4 must also be connected to PE 
ground (there are two PE terminals on the drive). See 

Figure 1.5

 for 

more information.

Parameter Configuration

The following PowerFlex 4 parameters are used to configure the drive to 
operate on a network. 

Supported Modbus Function Codes

The peripheral interface (DSI) used on PowerFlex 4 drives supports 
some of the Modbus function codes. 

Important:

Modbus devices can be 0-based (registers are numbered 
starting at 0) or 1-based (registers are numbered starting at 
1). Depending on the Modbus Master used, the register 
addresses listed on the following pages may need to be 
offset by +1. For example, Logic Command may be register 
address 8192 for some master devices (e.g. ProSoft 
3150-MCM SLC Modbus scanner) and 8193 for others 
(e.g. PanelViews).

Parameter

Details

Reference

P036 [Start Source]

Set to 5 “RS485 (DSI) Port” if Start is controlled from 
the network.

Page 3-9

P038 [Speed Reference]

Set to 5 “RS485 (DSI) Port” if the Speed Reference is 
controlled from the network.

Page 3-11

A103 [Comm Data Rate]

Sets the data rate for the RS485 (DSI) Port. All nodes 
on the network must be set to the same data rate.

Page 3-23

A104 [Comm Node Addr]

Sets the node address for the drive on the network. 
Each device on the network requires a unique node 
address.

Page 3-23

A105 [Comm Loss Action] Selects the drive’s response to communication 

problems.

Page 3-24

A106 [Comm Loss Time]

Sets the time that the drive will remain in 
communication loss before the drive implements A105 
[Comm Loss Action].

Page 3-24

A107 [Comm Format]

Sets the transmission mode, data bits, parity and stop 
bits for the RS485 (DSI) Port. All nodes on the network 
must be set to the same setting.

Page 3-24

Modbus Function Code

Command

03

Read Holding Registers

06

Preset (Write) Single Register

userman.book  Page 2  Friday, June 21, 2002  2:48 PM

Содержание Allen-Bradley PowerFlex 4































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды