manualshive.com logo in svg

Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series, Руководство по установке

Поделиться
Скачать
Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series Скачать руководство пользователя страница 49

Rockwell Automation Publication MM-IN001B-EN-P - February 2022

49

Kinetix MMA Asynchronous Main Motors Installation Instructions

Replace, Inspect, and Maintain Blower Filters

Filter media is made of synthetic fiber and has a corrugated matte to help increase the effectiveness. It must be properly cleaned and maintained to be effective.

Axial Blower Filter

There is no axial filter available. The customer is responsible for any filtering and impacts of airflow that would occur because of an installed blower filter.

Radial Blower Filter

On motors equipped with a filter, periodically inspect, clean, or replace the filter. If a filter is installed, avoid operating a motor without a filter in place. The air filter must 
always be kept in good working condition. Dirty air filters affect the performance of the motor and may cause overheating and the intervention of the thermal switches. 

A clogged air filter is directly related to the degree of impurity of the intake air, and so it is not possible to say what the average time between inspections and cleanings is. 
Normally, conduct cleaning about every 200 working hours, however, there are cases when the work is required more frequently.

Radial blower filters must be inspected, cleaned, and replaced regularly. Air 
filters are not provided as a replacement part from Rockwell Automation. Use 
the information in 

Table 51

 to source a filter. To replace a radial blower filter, 

follow these instructions:

1.

Remove power from the motor and de-energize the system.

2.

Loosen the screws that secure the filter to the blower air inlet.

3.

Slide the filter out.

4.

Clean or replace the filter. See 

Figure 18

.

• Blow out filter. 

When blowing out the filter, apply compressed air from the 
internal surface of the filter outward, being careful not to blow the 
dirt inside the motor. See 

Figure 18

.

• Replace filter. See 

Table 51

 for filter dimensions.

5.

Reinstall filter.

6.

Insert and hand-tighten the screws that secure the filter.

Table 50 - Radial Blower with 3-PH Input Voltage

Motor Cat. No.

Power Supply (V AC)/Hz

Max Current (A)

Power (kW)

Max Airflow 

(m

3

/min)

Max Pressure (Pa)

Blower Kit 

(1)

(1)

The ‘2B’ indicates that the blower kit fits both a brake and non-brake configuration, MM-BLWR-

xxx

-

2B

-x.

MMA-B132

xxx

3-PH; 380…420V AC; 50 Hz / 
440…480V AC; 60 Hz

0.75

0.25

15

800

MM-BLWR-132-2B-C

MMA-B160

xxx

3-PH; 380…420V AC; 50 Hz / 
440…480V AC; 60 Hz

2.31

1.10

30

1400

MM-BLWR-160-2B-C

MMA-B180

xxx

3-PH; 380…420V AC; 50 Hz / 
440…480V AC; 60 Hz

3.14

1.50

35

1600

MM-BLWR-180-2B-C

MMA-B225

xxx

3-PH; 380…420V AC; 50 Hz / 
440…480V AC; 60 Hz

4.51

2.20

48

1800

MM-BLWR-225-2B-C

SHOCK HAZARD: 

To avoid an electric shock hazard, verify that the voltage has discharged completely before servicing.

Table 51 - Radial Blower Filter Specifications

Filter Dimensions

Motor Cat. No.

Dimensions 
mm (in.)

Filter Folds

MMA-B132

xxx

245 x 220 x 48 (9.6 x 8.7 x 1.9)

5

MMA-B160

xxx

300 x 260 x 48 (11.8 x 10.2 x 1.9)

6

MMA-B180

xxx

350 x 350 x 48 (13.8 x 13.8 x 1.9)

7

MMA-B225

xxx

440 x 440 x 48 (17.3 x 17.3 x 1.9)

8

NOTE: 

When 

cleaning filter, blow 
compressed air 
from the internal 
surface outward.

Air filter path.

Remove 
screws (x2)
(hand-tighten)

Figure 18 - Radial Filter Replacement

Содержание Allen-Bradley Kinetix MMA-B080 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды