manualshive.com logo in svg

Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series, Руководство по установке

Поделиться
Скачать
Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series Скачать руководство пользователя страница 22

22

Rockwell Automation Publication MM-IN001B-EN-P - February 2022

Kinetix MMA Asynchronous Main Motors Installation Instructions

Wiring the Motor Terminal Box

The motor terminal board has three or six pins to connect the Kinetix MMA main motor windings. Additional terminals are available for the connection of the thermal 
protections and other accessories. See the Knowledgebase article: 

Kinetix MMA Frequently Asked Questions

, for additional information.

.

Figure 7 - Motor Terminal Board Configurations

IMPORTANT

The customer must supply motor power, brake, and accessory cables for the Kinetix MMA Asynchronous 
Main Motors. It is the responsibility of the customer to properly ground and terminate all connections in 
the terminal boxes. The recommended wire size is based on motor current requirements and terminal 
board sizing. Consult your local electrical code before you select the wire gauge for your application. 

Table 15 - Possible Motor Terminal Board Terminations and Definitions

Label

Description

Label

Description 

(1)

(1)

Resistive temperature device (RTD).

U1, V1, W1

Incoming power connections

TS

Thermostat for winding overheating protection

U2, V2, W2

Existing power connections

PT1000 Winding

RTD for real-time winding temperature measurements

Heater

Option: space heater

PT100 Front Bearing

RTD embedded in front bearing for real-time temperature measurements

Brake

Brake power and control

PT100 Rear Bearing

RTD embedded in rear bearing for real-time temperature measurements

Brake Status (microswitch)

NC - normally closed
NO - normally open
COM - common

KTY 84-130

RTD embedded in the windings and is used in place of the PT1000

Shaft Height 80

Shaft Height 100

Shaft Height 132 and 160

Shaft Height 180 and 225

Note

: This terminal only exists on the 

SH225, 400V AC brake option H

x 

and J

x.

Содержание Allen-Bradley Kinetix MMA-B080 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды