Roche OMNI C Скачать руководство пользователя страница 37

Страница: 37 / 152

1 Introduction

Instructions for Use, Roche OMNI C, Rev. 4.0, December 2002

1-29

1.9

Shutdown

1.9.1 Less than 24 hours

If the Roche OMNI C will be needed within the next 24 hours, press:

and

"System > Tools > Software shutdown"

and switch the instrument OFF.

1.9.2 Longer than 24 hours

If the Roche OMNI C will be shut down for longer than 24 hours, perform the following
procedure.

TIP:

Before shutting down the instrument, backup the data to a PCMCIA card or an inter-
face (see chapter 8, "Operating modes", section "Database").

TIP: Roche Diagnostics recommends decontaminating all surfaces and tubing before
shutting down the instrument. Please see chapter 6, "Maintenance", section "Decon-
tamination", for a detailed description!

While in the "Analyzer" operating mode, press:

and

"System > Tools > Shutdown"

Follow the instructions on the screen.

Confirm every step with

1. Remove bottles

•

Open the bottle compartment cover and remove bottles C1, C2, C3.

2. Remove the V2 and V9 tube ends from the guides

•

Remove the air mixture valve tube (valve V2) from the guide.

Содержание OMNI C

























































































































































Результаты поиска

Содержание OMNI C

Отзывы:

Бренды по названию

Популярные бренды

Roche OMNI C, Инструкция по эксплуатации

Результаты поиска

Содержание OMNI C

Отзывы:

Бренды по названию

Популярные бренды