Roche OMNI C Скачать руководство пользователя страница 126

Страница: 126 / 152

7 Trouble shooting

7-6

Instructions for Use, Roche OMNI C, Rev. 4.0, December 2002

7.2.9 3012 User system stop

Cause

•

The automatic fluidic procedure completion of some system stops can be interrupted by
a User system stop (by pressing the "Stop" button), e.g. in order to get immediate access
to the "More functions" button.

Remedy

•

Press the "OK" button (terminate the "User system stop")

•

In case of recurrence, call customer service!

Consequence actions

•

Aspirate Mix1

7.2.10 3013 Fluid pack switch

Cause

•

The docking mechanism of Fluid Pack C3 has been opened (micro switch activated)

•

The Fluid Pack C3 docking mechanism micro switch is defective

Remedy

•

Close docking mechanism Fluid Pack C3

•

Check micro switch ("More functions > System > Test > Control sensors > Monitoring
sensors"),.

•

In case of recurrence, call customer service (change if necessary)!

Consequence actions

•

Auto-preparing of Fluid Pack C3 solutions

7.2.11 3014 Fill level alarm

Cause

•

The solutions C1, C2 and/or C3 are empty (below alarm level) or are set to "empty"

•

The Waste container W is full (above alarm level)

•

The expiry date of the solutions is exceeded

•

The on-board lifetime of the solutions is exceeded (C1/C2 = 28 days; C3 = 42 days)

Remedy

•

Change solutions C1, C2 and Pack C3

•

Change or empty the Waste container W according to the instructions

•

In case of recurrence, call customer service!

Consequence actions

•

C1 changed: prepare solution C1, fill FMS reservoir, conductivity calibration

•

C2 changed: prepare solution C2, fill FMS reservoir, conductivity calibration

•

C3 changed resp. C3 docking mechanism micro switch operated: prepare C3 solutions

•

Waste container changed resp. micro switch operated: Waste container fill level
measurement

Содержание OMNI C

























































































































































Результаты поиска

Содержание OMNI C

Отзывы:

Бренды по названию

Популярные бренды

Roche OMNI C, Инструкция по эксплуатации

Результаты поиска

Содержание OMNI C

Отзывы:

Бренды по названию

Популярные бренды