Rocal ARc 73 TC +Plus 180, Руководство пользователя

Страница: 10 / 48

10
1.1 Technical specifications
Parameter
Modelo
ARc 73 TC ARc 73 TC +Plus 180 ARc 93 TC ARc 93 TC +Plus 180
Minimum - Maximum draught 11-13 Pa
Fuel consumption 3,4 kg/h 2,8 kg/h 3,5 kg/h 3,56 kg/h
Smoke mass flow rate 11,57 g/s 10,37 g/s 11,71 g/s 11,3 g/s
Performance 80,8 % 85,01 % 79 % 79.6%
Nominal output 11,4 kw 11 kW 12,1 kW 14,4 kW
Power range 7,5 – 13 kW 7,5– 13 kW 8,5 – 14,5 kW 8.5 – 14.5 kW
Average CO concentration at 13% of O
2
0,11 % 0,09% 0,07% 0,085%
Average NO
x
concentration at 13% of O
2
104,89 mg/Nm 3 71,50 mg/Nm 3 82,72 mg/Nm 3 126 mg/Nm 3
Average OGC concentration at 13% of O
2
98,78 mg/Nm 3 36,69 mg/Nm 3 52,66 mg/Nm 3 48 mg/Nm 3
Particle concentration at 13% of O
2
39,81 mg/Nm
3
38,69 mg/Nm
3
39,50 mg/Nm
3
20,20 mg/Nm
3
Medium draft (trial) 11 Pa 11,3 Pa 10 Pa 11,2 Pa
Net weight 114 kg 132 kg 161 kg 171,9 kg
Maximum authorized load (fuel) 3.5 kg 3.5 kg 5 kg 5 kg
Reload height 200 mm 200 mm 200 mm 200 mm
Logs length 450 mm 450 mm 600 mm 600 mm
Minimum flue height 4000 mm
Ø Flue duct 180 mm
Ø Air inlet 100 mm
Ø Air outlet 120 mm
Inner fireplace room safety distances (back) 50 mm 50 mm 50 mm 50 mm
Inner fireplace safety distances (sides) 1000 mm 1000 mm 1000 mm 1000 mm
Outer fireplace safety distances (frontal) 1000 mm 1000 mm 1000 mm 1000 mm
Outer fireplace safety distances (sides) 1000 mm 1000 mm 1000 mm 1000 mm
Outer fireplace safety distances (back)
600 mm 600 mm 200 mm 200 mm
Fireplace room ventilation (entry - exit) 450 cm 2
Electrical wiring connection Silicone hose 3*wire of 1.5 mm
2
Fan airflow (unit) 135 m 3 /h
Fan output (unit) 20 W
Minimum safety distance to the air outlets 2 2 4 4
Average temperature of smoke 250 mm
Type of combustion 217 ºC 178º C 250ºC 261,4ºC
Flue liner INTERMITENT
Fuel NOT SHARED
Humidity fuel logs NATURAL WOOD
Certification year 12-20 % - two years under cover
Certificate number 2019 2017 2019 2021
Electrical wiring connection 19/20678-18601/2 17/14327-852/853 M3 19/20678-1856-1/2 1880-CPR-024-21
1.2 Breakdown of delivery components
(Make sure you have all the components described below in relation to the picture on section II of the ANNEXED document)
1. Fireplace’s body.
2. Heat-resistant spray paint for touch-ups.
3. Fire grate.
4. Heat-resistant glove.
5. Cleaning cloth
6. Exterior air inlet kit. (Exterior air inlet connector, connector support, tubular joint, metallic anchor, screws and nuts)
7. Tool for handling registers and opening door.
8. Documentation bag: output declaration, energy label, guarantee, technical sheet, and installation and operating
characteristics manual.
9. Bag with screws.
10. Outlet hot air connector (2x ARc 73 TC | ARc 73 TC +Plus 180, 4x ARc 93 TC | ARc 93 TC +Plus 180)
11. Optional: + Plus 180 (ARc 73 TC +Plus 180 | ARc 93 TC +Plus 180)
1.3 Diagram of the equipment's measurements
See the ANNEXED document, section I, page 1.
ALL LOCAL STANDARDS, INCLUDING NATIONAL AND EUROPEAN REGULATIONS MUST BE COMPLIED WITH UPON
INSTALLATION OF THE EQUIPMENT.
THE INSTALLATION MUST BE PERFORMED BY A PROFESSIONAL. FAILURE TO COMPLY WITH THIS CLAUSE SHALL
EXONERATE THE MANUFACTURER FROM ANY RESPONSIBILITY.
2.1 Ground. Make sure the ground where the appliance will be placed is able to support the weight of the device. If not, you will need
a load spreading plate for the equitable distribution of the equipment's weight. In case of doubt, please consult a specialist.
2.2 Flue liner. It is mandatory to have a smoke-tight Flue liner going from the connecting point of the base to the outside in observation
of the smoke pipe diameter. The good condition and suitability of this smoke pipe must be certified by a professional and
must also observe the relevant national regulations . This flue liner must be T400 and G type should not be shared with other
devices (see Table 1.1 Technical specifications). In cases of too much draught, when the duct exceeds 7 meters in length, or the
measurement exceeds 20 Pa, the draft must be adjusted. To do this, use the second part of the baffle plate, to install it follow the
1. SPECIFICATIONS
2. REQUIREMENTS PRIOR TO INSTALLATION