manualshive.com logo in svg

Robin SmartPAT 5500, Руководство пользователя

Поделиться
Скачать
Robin SmartPAT 5500 Скачать руководство пользователя страница 6

Load
Load Measurement

0.1kVA to 3.99kVA

Display Resolution

0.1kVA

Display Accuracy

±(5% + 4 digits), resistive or reactive load

Abort on Surge

> 60 A exponential, time constant 50 ms

Abort on Run Current

> 13 A (235 V), > 16 A (110 V)

Test Duration

5s to 60s,Terminating immediately
when STOP button pressed.

Flash Test
Open Circuit Voltage

1500Vrms (Class I), 3000vrms (Class II)

Short Circuit Current

5mA at normal mains input

Display Resolution

0.1mA

Display Accuracy

±(5% + 4 digits)

Test Summary

The following statements provide a brief summary of the tests performed by the SmartPat 5500.

Earth bond
Checks the resistance between the Earth pin of the appliance under test and any exposed metalwork on
the appliance.

Insulation
Checks the resistance of the insulation between the Earth pin of the appliance under test cable plug or
the earth bond crocodile clip, to the Live and Neutral pins of the appliance (pins are connected together
within the SmartPAT 5500 for this test).

Fuse/Load/Leakage
A low dc fuse test is performed first to check the continuity of the fuse in the appliance under test, by
checking the resistance between the Live and Neutral pins of the appliance cable plug. On completion of
the fuse test an earth leakage test and a VoltAmpere test is performed with the appliance under test being
powered up.

Flash
A 1.5kV rms voltage is applied between the earth and live/neutral pins of a class I appliance and 3 kV rms
voltage between the flash probe and the live/neutral pins of a class II appliance.

SmartPAT 5500

5

7681 - 5500 PAT Manual 2002  7/26/02  11:14 AM  Page 7

Содержание SmartPAT 5500





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды