background image

7

5.Direct haze

Press the button FUNCTION until the display indicates »Direct Haze«. Press the button MANUAL to activate 

the direct haze mode. Then the machine directly starts producing haze after switching on the power. The dis-

play indicates »Direct Haze« and starts flashing. To stop the haze output, shortly press the button MANUAL 

again. The display stops flashing.

*Note 1:

 The control of the master unit will override the control of the panel controller when connecting the 

haze machine via DMX. 

*Note 2:

 If the haze outlet door sensor is activated (indication »DOOR ON SENSOR«), a warning sound will 

beep when haze output is activated and the door is not completely open. The flashes and indicates »DOOR 

CLOSED!!«. The haze production stops until the door is completely opened. If the door sensor is not activated 

(indication »DOOR OFF SENSOR«), this safety features will not occur.

*Note 3:

 If the displays shows »Out Of Order«, the machine’s internal temperature is too high and as a result 

the thermostat has been set off to shut-down the hazer.

If you experience this problem, please check two points as described below:

1. Check if the mesh (filter) outside the ventilation fan is clean and without debris. If the mesh is covered by 

dust or obstruction (such as paper, plastic bag, etc.), the machine is put into a very poor ventilation condition 

and causes the internal temperature to rise. Therefore, it is strongly suggested to clean the mesh regularly.

 2. Check the surrounding temperature at the hazer’s place of installation. If the temperature of the surrounding 

environment is too high, please move the machine to a cooler place with better ventilation.

*Note 4:

 Before moving the machine, it is important to replace the nozzle by the black rubber stopper. Please 

make sure it fits tightly in order to prevent spillage of the hazer liquid in case the machine is turned upside 

down during the transportation. Before reusing the machine, please put the nozzle back on the outlet and 

make sure it is properly installed.

DMX Connector Pin Assignment

The machine provide 3 or 5 pin XLR connector for DMX connection. Diagram below indicate pin assignment 

information

 

 

3-pin XLR 

 

 

 

 

 

5-pin XLR

  

Содержание HAZE 500 FT PRO









Отзывы: