RKI 65-2443SS Series Скачать руководство пользователя страница 3

 

65-2443SS-XX PPM Hydrogen Transmitter • 3

Product Warranty

RKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in materials, 
workmanship, and performance for a period of one year* from the date of shipment from RKI 
Instruments, Inc. Any parts found defective within that period will be repaired or replaced, at our 
option, free of charge. Parts must be returned to RKI Instruments, Inc. for repair or replacement. This 
warranty does not apply to those items which by their nature are subject to deterioration or 
consumption in normal service, and which must be cleaned, repaired or replaced on a routine basis. 
Examples of such items are:

Warranty is voided by abuse including mechanical damage, alteration, rough handling, or repair 
procedures not in accordance with instruction manual. This warranty indicates the full extend of our 
liability, and we are not responsible for removal or replacement costs, local repair costs, transportation 
costs, or contingent expenses incurred without our prior approval.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER WARRANTIES 
AND REPRESENTATIONS, EXPRESSED OR IMPLIED, AND ALL OTHER 
OBLIGATIONS OR LIABILITIES ON THE PART OF RKI INSTRUMENTS, INC. 
INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL RKI INSTRUMENTS, 
INC. BE LIABLE FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL LOSS OR 
DAMAGE OF ANY KIND CONNECTED WITH THE USE OF ITS PRODUCTS OR 
FAILURE OF ITS PRODUCTS TO FUNCTION OR OPERATE PROPERLY.

This warranty covers instruments and parts sold to users only by authorized distributors, dealers and 
representatives as appointed by RKI Instruments, Inc.

We do not assume indemnification for any accident or damage caused by the operation of this gas 
monitor and our warranty is limited to the replacement of parts or our complete goods. Warranty 
covers parts and labor performed at RKI Instruments, Inc. only, and does not cover field labor or 
shipment of parts back to RKI. 

a) Pump diaphragms and valves

c) Batteries

b) Fuses

d) Filter elements

Содержание 65-2443SS Series





















Отзывы: