4 IMCB02-E5
4. NAME OF PARTS
5. SETTING
5.1 Calling up procedure of each mode
5.2 Detail of each mode
"#
PV/SV display mode
Display measured value (PV) on the PV display unit and set
value (SV) on the SV display unit. Usually the control is set to this
mode excepting that the set value (SV) and/or the parameter set
value are changed.
In addition, in this mode, RUN/STOP can be selected.
"#
SV setting mode
This is the mode used to set the set value (SV).
Factory set value : 0
°
C[
°
F ] or 0.0
°
C[
°
F ]
"#
Parameter setting mode
This is the mode used to set the various parameters such as
alarms, PID constants, etc.
The following parameter symbols are displayed one by one every
time the
SET
key is pressed.
"#
Communication setting mode
This is the mode to conduct settings relating to the
communication function. It is displayed for the instrument with the
communication function. For details on protocol, identifiers and
communication setting mode, see the separate instruction
manual for “
Communication
” (
IMCB03-E
$
$
$
$
).
SET
SET
SET
Power ON
Input type display
Input range display
PV/SV display mode
SV setting mode
Parameter setting
Communication
setting mode
Display changes automatically
mode
+
(Display for
approx.4 sec)
**
*1
(Normal display)
***
*
** Press the
SET
key for more than 2 sec.
***Press the
<R/S
key while pressing the
SET
key.
* The
RUN/STOP
function can be selected.The
RUN/STOP
function
can be selected every time the
<R/S
key is pressed for 1 sec.
not performed for more than 1 minute.
The instrument returns to the PV/SV
display mode status if key operation is
R/S
1
2
3
4
5
6
7
AT
OUT1
OUT2
ALM1
ALM2
R/S
CB500
PV
SV
SET
C
C
C
C
1
2
4
5
6
7
3
AT
OUT1
OUT2
ALM1
ALM2
SET
R/S
CB400
PV
SV
C
C
C
C
%
%
%
%
Measured value (PV) display unit
[Green]
•
Displays measured value (PV).
•
Displays various parameter symbols
depending on the instrument
.
&
&
&
&
Set value (SV) display unit [Orange]
•
Displays set value (SV).
•
Displays various parameters set value
(or CT input value)
depending on the
instrument.
'
'
'
'
Indication lamps
Alarm output lamps (ALM1,ALM2) [Red]
ALM1: Lights when first alarm output is
turned on.
ALM2: Lights when second alarm output
is turned on.
*1. Input type and input range display
This instrument immediately confirms input type and range
following power on.
Example: For a controller with the K thermocouple input type and
range from 0 to 1372
°
C.
Autotuning (AT) lamp [Green]
Flashes during autotuning execution.
Control output lamps (OUT1,OUT2)
[Green]
OUT1: Lights when control output is
turned on. **
OUT2: Lights when cool-side control
output is turned on.**
** Lamp indication becomes as follows
for continuous output.
For an output of less than 0 % :
Extinguished
For an output of more than 100 % : Lit
For an output of more than 0 % but less
than 100 % : Dimly lit.
SV
PV
PV
SV
%
&
b
a
(
(
(
(
Set key
Used for parameter registration/calling
up.
)
)
)
)
Shift & R/S key
•
Used to shift the digit when the setting
is changed.(Shift key)
•
Used to select the RUN/STOP function.
(R/S key)
*
*
*
*
DOWN key
Used to decrease numerals.
+
+
+
+
UP key
Used to increase numerals.
%
Input type display
&
Input range display
a : Input range high
b : Input range low
**A: Input type table
1
2
3
4
5
6
7
PV
SV
AT
OUT1
OUT2
ALM1
ALM2
R/S
SET
CB900
C
CB500
CB700,CB900
CB400
K J R S B E T N
U L
PL
W5Re/
100
Pt
Display
Input
type
W26Re
Voltage
100
Thermocouple (TC)
RTD
II
(Current)
JPt
SET
R / S
:Input symbol
:Engineering unit.
( :
°
F)
[Voltage/current input: No display]
:Input type
(See table
**A
.)
