Riverside Hydronics EPV SERIES Скачать руководство пользователя страница 1

34-501 07/13 

INSTALLATION & MAINTENANCE MANUAL 

 

EPV SERIES CONDENSING WATER BOILER 

 

 

Installation and service must be performed by a qualified service installer, service agency or the gas supplier. 

 

IMPORTANT: THIS MANUAL CONTAINS INFORMATION REQUIRED FOR INSTALLATION, OPERATION AND 
MAINTENANCE OF THIS EQUIPMENT.  READ AND FOLLOW THE INFORMATION IN THIS MANUAL AND ALL 
OTHER PROVIDED INSTRUCTIONS, LABELS AND MARKINGS BEFORE INSTALLING, OPERATING OR 
SERVICING THIS UNIT.

 
 

FOR YOUR SAFETY 

 

Do not

 store or use gasoline or other flammable vapors or 

liquids in the vicinity of this or any other appliance.

 

 

WHAT TO DO IF YOU SMELL GAS 

 

Do not

 try to light any appliance. 

 

Do not

 touch any electric switch; do not use any phone in your 

building. 

 

Immediately

 call your gas supplier from a neighbor's phone. 

Follow the gas supplier's instructions.

 

 If you cannot reach your gas supplier, call the fire department

 

 

This product contains, or may come to contain materials identified 
as carcinogenic, or possibly carcinogenic to humans.  Before 
installing, servicing or removing this product, read and follow the 
supplied instructions. 

 
 

 
 

 
 
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, 
personal injury, exposure to hazardous materials or loss of life.  Refer to the information contained in this 
manual.  A qualified installer, service agency or the gas supplier, who must read and follow the supplied 
instructions before installing, servicing or removing this appliance, must perform installation and service.  This 
appliance contains, or may come to contain materials that have been identified as carcinogenic, or possibly 
carcinogenic to humans.

 

 

WARNING: Do not use this appliance if any part has been under water.  Immediately call a qualified service 
technician to inspect the unit and to replace any part of the control system, any gas controls and any other items 
affecting safe appliance operation and which has been under water.  Failure to follow these instructions can 
cause property damage, personal injury, exposure to hazardous materials or loss of life.

 

 
 

 
TO THE INSTALLER:

  After installation, these instructions must be given to the equipment user or left near the appliance.

 

 
SPECIAL INSTRUCTIONS TO THE OWNER:

  Retain this manual for future reference. These instructions contain 

important information that will help you in maintaining and operating this appliance. 

 

 
 
 
 
 

 
 
 

 

 
 
 
 

  

 

 
Riverside Hydronics

®

, LLC - 990 Haltom Road - Fort Worth, Texas  76117 - Tel 1-800-990-5918 

 

 

Содержание EPV SERIES























Отзывы: