background image

Check for parts online at 

www.HuntRiversEdge.com

 or call 800-450-EDGE (3343) M-F 8-5

11

Operator's Manual

Rivers Edge® Uppercut™

16. Sections are assembled on the ground in the following order; 

bottom section (10166 3-step ladder); second section (10168 3-step 
ladder with stabilizer bar hole); third section (10168 3-step ladder 
with stabilizer bar hole); fourth section (10170 3-step ladder w/ 
support brace mounting holes); top section (assembled top platform 
section). 

SEE FINISHED UPPERCUT LADDER. 

17. With all sections assembled together on ground, secure all sections 

together using (3) provided spring lock pins. 

SEE FIGURE 19.

18. Attach the (2) support braces (410024) to the inside of lower tree 

blade and outside of top ladder section w/ mounting holes using 
(4) provided 1/4-20 x 1-1/2” bolts and locknuts. 

SEE FIGURE 20.

 

Tighten securely. Be sure not to over tighten or crush tubing 

when tightening!

19. a.   Attach the removable shooting rail by setting rail down over studs 

provided on armrests 

SEE FIGURE 21

. Lubrication is recommended 

to prevent binding and noise. 

 

b.   Attach the (2) provided 9” and (1) provided 47” camo foam pads 
to the armrests and shooting rail by wrapping around tubing and 
attaching Velcro® together. 

 

c.   Attach foam padded seat bumpers (48102) to bottom side of 
front seat spacer weldment.  Surface must be clean and at room 
temperature to assure proper adhesion.

20. a. Attach the stabilizer bar extension tube (48053) to the second 

ladder section mounting hole using (1) provided 1/4-20 x 2-1/4” 
wing bolt and wing nut. 

SEE FIGURE 22.

 

b. Slide the stabilizer bar (48052) into the extension tube and attach 
the two pieces together using (1) provided spring lock pin. Spring 
lock pin must go through both the extension tube and stabilizer 
bar at appropriate hole to achieve desired distance from tree. 
Adjustment in length may be needed when ladder is uprighted later 
in instructions. 

SEE FIGURE 22.

21. Tie one end of each of the provided 20’ ropes to the square tube of 

tree blade frame, just in front of the tree blades. Be sure your double 
knots are secure.

 SEE FIGURE 23.

Figure 20

1/4-20 x 1-1/2" bolts

locknuts

1/4-20 x 1-1/2" bolts

Figure 21

Figure 22

extension tube

1/4-20x 2-1/4 wing bolt

1/4-20 wing nut

stabilzier bar

snap lock pin

Figure 19

Figure 23

Содержание Uppercut RE632





















Отзывы: