background image

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5

17

Operator's Manual

LOCKDOWN 2-MAN Ladder Stand

READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP AND USE

STOP

WARNING

Bring ratchet strap(s) up with you in a pocket - Do Not 

carry in your hands!

WARNING

Double check assembly steps to be certain you have 

correctly assembled this product.
Study your new stand to become familiar with all of its 

features and design. At ground level, following provided 

use instructions, practice attaching stand to tree and 

removing stand from tree. Practice sitting, standing, and 

using this product before attaching overhead. Save these 

instructions for future reference. You must always use the 

provided Fall Arrest System (FAS) while using this product.
Always use at least three (3) people to install or take down 

a ladder treestand. Always have two people stabilize the 

ladder before climbing to the platform the first time after 

every set-up.
Be absolutely sure the tree blade(s) on stand and the 

stabilizer bar are contacting tree before climbing ladder.
Stabilizer bar must always be correctly and securely 

attached to ladder and tree before climbing ladder.
Make sure ladder bottom is firmly seated on dry, level 

ground. Attach your harness tether to the tree before 

securing the platform to the tree and stepping onto 

platform. Refer to the Full Body Harness instructions.
Never ascend or descend ladder without straps/ropes 

securely holding ladder to tree and stabilizer bar securely 

attached. Failure to correctly perform these steps can 

cause the ladder to collapse/buckle-over backwards 

during the initial ascent to attach ratchet strap resulting 

in serious injury or death.
Always lean forward as you climb and attach your harness 

to the tree before securing the platform to the tree with 

the provided ratchet straps.

WARNING

Always maintain three (3) points of contact when 

climbing a ladder treestand. Proper three-point contact 

means having either two feet with one hand or one foot 

with two hands on the step portion of the ladder or 

climbing aid at all times.
Always wear the appropriate footwear when using a 

ladder treestand. A good non-slip safety boot is important 

to your personal safety. Be especially careful that boot laces 

do not get hooked on the stand or any of its components 

(tuck shoelaces into boots before climbing).
Never stand on seat, it is designed for sitting only.
Do Not allow excessive strap buildup in ratchet as this 

will prevent the ratchet teeth from engaging causing 

slippage.
Always attach ratchet straps securely while using this 

product!
If seat is removable, be certain it is securely attached 

when in use.
Some models include a shooting rail. Never lean against, 

lean over, or sit on shooting rail. It is designed as a 

shooting rest only. Always be aware that the shooting rail 

can swing to one side or pivot up and down.
Some models include a footrest, which is designed as a 

footrest only. Never stand on footrest! Always be fully 

aware of foot placement.
Some models include a multi-piece stabilizer bar system. 

Be sure attachment hardware goes through all extension 

tubes of the stabilizer bar.

Содержание LD203





























Отзывы: