Rittal DK 7320.240 Скачать руководство пользователя страница 13

Страница: 13 / 20

Commissioning 7

CMC-TC Wireless I/O-Unit

7.5.3 Wireless System Range Estimate

Table 5 provides an indication of the expected ran-
ges for certain installation scenarios.

Scenario

Sensor range

Single enclosure

for steel door (closed)

up to 20m

for steel door (70% vented)

up to 35m

for glazed door

up to 45m

Single enclosure (side)

for steel door (closed)

up to 20m

for steel door (70% vented)

up to 25m

for glazed door

up to 25m

Note: These values are highly dependent on the
ambient reflection

Enclosure suite

for steel door (closed)

up to 6m

for steel door (70% vented)

up to 20m

for glazed door

up to 30m

Enclosure suite (side)

for steel door (closed)

up to 6m

for steel door (70% vented)

up to 10 m

for glazed door

up to 10 m

Note: These values are highly dependent on the
ambient reflection

Adjoining room (masonry: thickness 30 cm, concrete)

for steel door (closed)

up to 6m

for steel door (70% vented)

up to 8m

for glazed door

up to 10 m

Corridor (line of sight, LOS)

up to 50 m

Outdoor (line of sight, LOS)

up to 200m

Industrial building (line of sight, LOS)

up to 50 m

Tab. 5 Wireless ranges

Содержание DK 7320.240





















Результаты поиска

Содержание DK 7320.240

Отзывы:

Похожие инструкции для DK 7320.240

Бренды по названию

Популярные бренды

Rittal DK 7320.240, Инструкции по сборке, установке и эксплуатации

Результаты поиска

Содержание DK 7320.240

Отзывы:

Похожие инструкции для DK 7320.240

Бренды по названию

Популярные бренды