2
2. Pressing Include button three times
within 2 seconds will enter inclusion
mode.
Exclusion
(Remove an
existed node)
1. Put your Z-Wave controller into
exclusion mode by following the
instructions provided by the
controller manufacturer.
One press one flash LED
2. Pressing Include button three
times within 2 seconds will enter
exclusion mode.
Node ID has been excluded.
LED 0.5s On, 0.5s Off
(Enter auto inclusion)
Reset
1. Pressing Include button three times
within 2 seconds will enter inclusion
mode.
Use this procedure only in
the event that the primary
controller is lost or
otherwise inoperable.
2. Within 1 second, press Include
button again for 5 seconds.
3. IDs are excluded.
LED 0.5s On, 0.5s Off
(Enter auto inclusion)
Association
1. The PAN11 is an always listening
Z-Wave device, so associations
be added or removed by a controller
at any time.
Or If your controller requires to have
the PAN11 send a 'node information
frame' or NIF for associations,
pressing the On/Off button three
times within 2 seconds will cause
the PAN11 to send its NIF.
LED One press one flash
2. There are 1 group (Group 1) for the
PAN08
Adding a node ID allocated by Z-Wave Controller means inclusion. Removing a node ID
allocated by Z-Wave Controller means exclusion.
Failed or success in including/excluding the node ID can be viewed from the Z-Wave
Controller.
LED Indication
To distinguish what mode the PAN08 is in, view from the LED for identification.
State Type
LED Indication
Motor
activate
No matter up or down, close or open, Led will flash every second
while Motor activate.
When S1 or S2 close to L, the LED will flash even when the motor
stop by itself, this is to let user know the S1 or S2 still close and not
been release yet.
No node ID
Under normal operation, when the PAN08 has not been allocated a
node ID, the LED flashes on and off alternately at 2-second
intervals. By pressing S1 S2 or Include button, it will stop flashing
temporarily.
Learning
When PAN08 is in learning mode, LED flashes on and off
alternately and repeatedly at 0.5 second intervals.
Overload
When overload state occurs, the PAN08 is disabled and LED
flashes on and off alternately at 0.2 second intervals. PAN08 will
send alarm_type=8 alarm_Level=0xFF to Group1, Overload state
can be cleared by disconnect and reconnect the PAN08 to the main
power
Choosing a Suitable Location
1. Do not locate the PAN08 facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the PAN08 is 0°C~40°C.
3. Do not locate the PAN08 where exists combustible substances or any source of
heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of PAN08 will become a little bit hot of which
phenomenon is normal.
Moving Range Calibration
1. It is important to carry out a shutter calibration process before you control the
shutter to move. Press inclusion button over 3 seconds and release before the 6th
second, the roller shutter controller will start the shutter calibration process. The
process is composed of three continue stages. The shutter move to the TOP in first
stage, and move to the BOTTOM in second stage, and move to the TOP again in
third stage. Then PAN08 will know the total range of UP and DOWN.
2. During the shutter calibration process, any emergencies happen you can press
and release the include button to stop the process.
3. If user found the direction is reverse, this may cause by the wrong connection of
NC and NO to the motor, please exchange NC and NO connection and execute
calibration process again.
4. For safe issue, please select the motor which can stop by itself when go to bottom
end or top end.
