Rinnai RHEPM11530N Скачать руководство пользователя страница 4

 

4

 

HE+ Series Modulating Supplemental Manual

 

APPLICATION

 

HE+ Series models are modulating gas

-

fired radiant tube heaters

 

that may be installed for 

heating of commercial / industrial indoor spaces.

 

Not for use in residential dwellings.

 

residential dwelling

” 

is defined in the standard as 

a housekeeping unit used or intended to 

be used as a domicile by one or more persons, containing cooking, eating, living, sleeping, 
and/or sanitary facilities. A residential dwelling does not include an attached garage, detached 

garage, workshop or outdoors

”. 

Local Code requirements take precedence for this application.

 

It is beyond the scope of these instructions to consider all conditions and requirements that 

may be encountered in the field.  Installation must conform with all local codes or, in the ab-

sence of local codes, with the latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA 
54 in the U.S.A. The latest edition Electrical Code ANSI/NFPA No. 70 in the U.S.A. must also 

be observed. 

 

Installation of a gas fired tube heater must conform to all heating installation design procedures 

including clearance to combustibles, connection to the gas and electrical supplies, and ventila-

tion requirements. 

 

This heater is not for installation in a Class 1 or Class 2 explosive environment, nor in a resi-

dential dwelling. If installation of this equipment is in question, consult with the local authority 

having jurisdiction (Fire Marshall, labor department, insurance underwriter, or other). 

 

Revisions to codes and/or standards, may require revision to equipment and installation proce-

dures. In case of discrepancy, the latest codes, standards, and installation manual will take pri-

ority over prior releases. 

 

Improper installation, adjustment, alteration, service or maintenance can cause 
property damage, injury or death.  Read and understand this installation and op-
eration manual thoroughly prior to assembly, installation, operation or service to 
this appliance. 

 

This heater must be installed and serviced only by a trained gas service techni-
cian. 

 

Do not store or use gasoline or other flammable vapours and liquids in the vicinity 
of this or any other gas fired appliance.

 

Failure to comply could result in personal injury, death, fire and/or property dam-
age.

 

Do not store or use gasoline or other flammable vapours and liquids in the vicinity 
of this or any other gas fired appliance.

 

This appliance may have sharp edges and corners. Wear protective clothing such 
as gloves and protective eye wear when servicing this or any other appliance.

 

WARNING

 

California Proposition 65:

 

WARNING

: This product can expose you to chemicals including carbon monoxide, which 

is known to the State of California to cause birth defects or other reproductive harm. For more 
information, go to www.P65Warnings.ca.gov

 

Содержание RHEPM11530N





































Отзывы: