Arriva 752 operation guide: 12219-C 03-20 |
11
Setting the clock
The clock must be set before
the timers will operate.
Press the ‘Time Set’ button
once, ‘Clock Set’ will be
displayed to confirm the
function is initiated. The
remote will show ‘AM 12:00’.
Use the up and down buttons
to set AM or PM and set the
clock, then press ‘Time Set’ to
start programming the timers.
If you don’t want to set the
timers at this point, press
‘Time Set’ four times to return
to the clock. If no button is
pressed within 90 seconds,
the screen will deactivate and
the settings may be lost.
Setting the timers
After the clock has been set
and the ‘Time Set’ button
selected:
1. ‘Timer 1 Set On’
and ‘AM 06:00’
will be displayed.
Use the up and
down buttons to set AM or
PM. Press the Time Set
button once.
2. ‘Timer 1 Set Off’
and ‘AM 09:00’
will be displayed.
Use the up and
down buttons to set AM
or PM. Press the Time set
button once.
3.
To set up Timer 2 repeat
the above steps, or press
‘Time Set’ three times to
exit the timer program.
4. The set On/Off timers
will be displayed briefly
to confirm the settings.
When the programs have
been received the remote
display will revert to time
mode.
Using the timers
Prior to using the timers
ensure the desired
temperature has been set,
refer previous page.
You can view the timer
settings by pressing the
‘Timer 1’ or ‘Timer 2’ buttons
while the fire is operating.
The display will briefly show
the status of each timer, i.e.
Timer 1 On, Timer 1 Off. If the
current time is outside of the
programmed times the fire will
go into standby and the LED
will glow green.
To turn the timers off, press the
relevant timer button again.
The fire will return to standby.
If there are no timers set the
Timer Indicator will go out.
Preheat function
Preheat automatically
functions in conjunction
with the timers. The preheat
function ensures the room
reaches temperature by the
programmed on time. This is
achieved by sensing the room
temperature one hour prior to
start.
Override
This is used to manually
override the timers so the
fire can be operated outside
the timer periods. When
override is selected ‘Override’
will be displayed. While in
Override all remote functions,
except for flame function are
available until the next timer
period.
To return to the timer setting,
press ‘Override’ again. If
Standby / On is pressed
during override the fire will
revert to standby and the timer
programs will be cancelled.
Extra low
Useful in situations when the
room temperature keeps rising
even when the fire is on the
lowest setting.
Function off
When the room temperature
reaches the preset
temperature the fire continues
to operate with the main
burner on low, to provide a
flame picture with minimal
heat output. In some cases
this may cause the room to
become warmer than desired.
Function on
When the room temperature
exceeds the preset
temperature, the burner will
reduce to an extra low setting
and will return to normal if the
room temperature starts to fall
below the preset temperature.
Flame
Flame function
can be used
approximately 90
seconds after the
fire has started. The flame
function is used to select
a desired flame picture
and overrides automatic
mode
—
seven flame settings
available.
While the fire is operating
press the ‘Flame’ button. The
fire will automatically default
to the last flame setting. The
word ‘Flame’ and a series of
short bars will be displayed.
Use the up and down buttons
to select the desired flame
picture. The number of bars
illuminated will correspond to
your selection.
Should the room temperature
exceed 40 °C, while the flame
function is on, the fire will
switch off
—
this is a safety
feature.
AM
Timer 1
Set ON
AM
Timer 1
Set
OFF
AM
Time
Flame
Содержание Arriva 752
Страница 1: ...Arriva 752 gas fireplace Operation guide...
