RINGSPANN Brake HW 165 FHM Скачать руководство пользователя | Manualshive

Страница: 5 / 24

background image

Installation and operating instructions for

Brake HW 165 FHM spring activated

–

hydraulically released

E 09.774e

Issue: 08.01.2021

Version: 1

Drawn: BAHS

Checked: EISF Pages: 24

Page: 5

Life-threatening danger!

Disc must be absolutely degreased before all contact with the brakes
linings.

In case of lining pollution with grease, the nominal brake force is not
guaranteed.

Calipers are fail safe components.
All setting and repairs must be performed by skilled operators.

BE CAREFUL: The caliper is delivered in " manual release" position and
the holding force is adjusted in the factory.
Instructions in this manual must be followed up to chapter 2.4 inclusive
(INITIAL START-UP) to ensure that the brake is operational.

When assembling, operating and maintaining the brake it is to be
ensured that the entire drive train is secured against being switched on
unintentionally. Moving parts can cause severe injury. Rotating parts
(e.g. brake disc) must be secured by the operator against unintentional
touching.

Strongly pre-loaded pressure springs are installed in the springed
thrusters of the brake. The spring thruster may only be disassembled by
the factory.

2

Installation

2.1 Preparing the positioning area

Ensure that the positioning surface is clean and dry.
Make sure that there is sufficient space around the brake.
Check that the attaching holes are in conformity (center distances, sizes and numbers).

«
...
3
4
5
6
7
...
»

Содержание Brake HW 165 FHM

























Отзывы:

Нет отзывов

Похожие инструкции для Brake HW 165 FHM

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: i-SENS Страницы: 50

NANOCOLOR Advance

Бренд: Macherey-Nagel Страницы: 45

Бренд: Olympus Страницы: 12

Бренд: Xylem Страницы: 19

Бренд: Cecomp Страницы: 4

Бренд: FMS Страницы: 12

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: Dynojet Страницы: 88

Бренд: VP instruments Страницы: 15

Бренд: Tektronix Страницы: 20

FrameSaver SLV Series

Бренд: Paradyne Страницы: 39

Бренд: Opus Technologies Страницы: 24

Бренд: S&T Страницы: 23

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды