RINGSPANN Brake HW 165 FHM Скачать руководство пользователя

Страница: 21 / 24

Installation and operating instructions for

Brake HW 165 FHM spring activated

–

hydraulically released

E 09.774e

Issue: 08.01.2021

Version: 1

Drawn: BAHS

Checked: EISF Pages: 24

Page: 21

5.5 Opening and wear contacts (mechanicals) adjustment

Information!

Contacts are factory set and do not need any adjustment.
If necessary, follow this procedure.

Verify the gap for the pad at each caliper, otherwise perform all the operations in chapter 5.3.
Refer to the identification plate for the nominal clearance.

Tools: 2.5mm Allen wrench - 8mm AF spanner.

Fig. 5.7

5.5.1

Adjustment of ‘brake released’ switch

This switch monitors the status of the brake (closed or released)
It closes when the brake is released (set under pressure).

- Power the brake at 200bars.

- Unscrew nut

V11

(8 mm on flats)

- Check that the axle

is in contact onto lever

41.

- Adjust the screw HC

V02

(2.5 mm Allen wrench) until the activation of contact. Check that state

contact is "Open".

Opening contact

Wear contact

Содержание Brake HW 165 FHM

























Результаты поиска

Содержание Brake HW 165 FHM

Отзывы:

Похожие инструкции для Brake HW 165 FHM

Бренды по названию

Популярные бренды

RINGSPANN Brake HW 165 FHM, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Brake HW 165 FHM

Отзывы:

Похожие инструкции для Brake HW 165 FHM

Бренды по названию

Популярные бренды