RINGSPANN Brake HW 165 FHM Скачать руководство пользователя | Manualshive

Страница: 13 / 24

background image

Installation and operating instructions for

Brake HW 165 FHM spring activated

–

hydraulically released

E 09.774e

Issue: 08.01.2021

Version: 1

Drawn: BAHS

Checked: EISF Pages: 24

Page: 13

2.4.4 Control of the general running

Important!

Be Careful: The disc must be degreased and free from any deposits so as
not to decrease the friction coefficient.

Check the well running of the electric contacts.
Run the brake under no-load with the disc turning, 20 or so times, to bed in the pads.

Information!

THE SYSTEM IS NOW OPERATIONNAL

3

Operational RUNNING

3.1 Caliper tightening

The lack of hydraulic pressure allows the pads to be tightened on the disc.
The opening contact is not activated.

3.2 Caliper untightening

Apply a minimum pressure of 200bars to release the brake.
The opening contact is activated.

3.3 Caliper manual release

Manual release keeps the caliper open without hydraulic pressure.
Refer to chapter 5.1 and chapter 5.2.

«
...
11
12
13
14
15
...
»

Содержание Brake HW 165 FHM

























Отзывы:

Нет отзывов

Похожие инструкции для Brake HW 165 FHM

Бренд: TANDBERG Страницы: 53

Бренд: Danfoss Страницы: 8

Бренд: QLA Страницы: 18

Бренд: jablotron Страницы: 2

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: GE Страницы: 35

Бренд: Yamaha Страницы: 24

Бренд: Hanna Instruments Страницы: 2

Бренд: Teledyne Analytical Instruments Страницы: 107

Бренд: PASCO Страницы: 4

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

NOVAplus biogas

Бренд: mru Страницы: 78

Бренд: East Tester Страницы: 27

Бренд: LaMotte Страницы: 2

Бренд: VECTECH Страницы: 10

Бренд: Eddyfi Technologies Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды