manualshive.com logo in svg

Rigol DS70000 Series, Руководство пользователя, Страница: 30 / 43

Поделиться
Скачать
Rigol DS70000 Series Скачать руководство пользователя страница 30

5.4.3

Test Procedures

WARNING

Before connecting, disconnecting, or moving the test hookup, disable the output of the
signal generator to avoid causing the dangerous voltage.

1. The connection diagram is shown in the above figure:

a. Connect the [RF OUTPUT 50 Ω] connector of DSG3000B to the input of the

power splitter by using the N(M)-N(M) cable.

b. Connect the power meter probe (power sensor) to the output of the power

splitter.

c. Connect the other splitter output to CH1 of the oscilloscope by using the N(M)-

BNC(M) cable.

2. Set up the power meter: set the power meter to display measurements in watts.

3. Configure the oscilloscope:

a. Press the front-panel key 

 to enable CH1.

b. In the Vertical system menu, click or tap 50 Ω under Impedance to set the

input impedance of CH1 to 50 Ω. Set the vertical scale to 100 mV/div.

c. In the Horizontal system menu, set the horizontal timebase to 500 ns/div.

4. Output a Sine with 1 MHz frequency and 6 div amplitude (e.g. 5 mV/div vertical

scale, 30 mVpp Sine signal). Adjust the timebase to display five cycles of the

waveforms on the screen.

5. In the Measure menu, click or tap Vertical measurement item to select "AC.RMS".

The AC.RMS measurement result list is displayed at the right section of the screen.

Read the value from the "result" list and record the measurement result as Vout

1

MHz

.

6. Record the power meter reading P

1 MHz

, and convert the power to V according to

the following formula.

 Performance Verification Test

DS70000 Performance Verification

24

Copyright ©RIGOL TECHNOLOGIES CO., LTD. All rights reserved.

Содержание DS70000 Series












































Отзывы:

Нет отзывов