Rigol DS70000 Series Скачать руководство пользователя страница 27

Страница: 27 / 43

c. Click or tap the drop-down button of the BW Limit menu to select "20 M".

d. Set the vertical scale to 1 mV/div.

e. Set the offset to 1 V, as shown in the test record form. Close the Vertical system

menu.

f. Click or tap the horizontal menu ("D" icon) at the top of the screen. Then the

Horizontal system menu is displayed. In this menu, set the timebase to 1 ms/

div. Select "Average" for the Acquisition menu. Then click or tap the input field

for the Averages menu item to set it by using the pop-up numeric keypad. Set

the number of averages item to 16. Close the Horizontal system menu.

g. Click or tap the trigger information label at the top of the screen. Set Source to

AC Line.

h. Adjust the trigger level to avoid that the signals are being triggered by mistake.

4. Set the output of Fluke 9500B to -1 V.

5. In the Measure menu, click or tap Vertical measurement item to select "Vavg". The

Vavg measurement result list is displayed at the right section of the screen. Read

the value from the "result" list and record the measurement result.

6. Set the vertical offset of the oscilloscope to 0 V.

7. Set the output of Fluke 9500B to 0 V. Read the value from the "result" list and

record the measurement result.

8. Repeat Step 7-9. Measure and record the results according to

Test Record Form

5.3.4

Test Record Form

Channel

Setting

Vertical

Scale

Offset

Test Result

Min.

Max.

CH1, 1 MΩ,

20 MHz BW

1 mV/div

1 V

-1.0171 V

-982.90 mV

1 mV/div

0 V

-2.1000 mV 2.1000 mV

1 mV/div

-1 V

982.90 mV

1.0171 V

200 mV/div 30 V

-30.472 V

-29.528 V

200 mV/div 0 V

-22.000 mV 22.000 mV

200 mV/div -30 V

29.528 V

30.472 V

500 mV/div 100 V

-101.05 V

-98.948 V

500 mV/div 0 V

-52.000 mV 52.000 mV

Performance Verification Test

DS70000 Performance Verification

Содержание DS70000 Series










































Результаты поиска

Содержание DS70000 Series

Отзывы:

Rigol DS70000 Series, Руководство пользователя, Страница: 27 / 43

Результаты поиска

Содержание DS70000 Series

Отзывы: