manualshive.com logo in svg

Rigol DS70000 Series, Руководство пользователя, Страница: 15 / 43

Поделиться
Скачать
Rigol DS70000 Series Скачать руководство пользователя страница 15

Figure 4.1 Self-calibration Menu

- Click or tap Start, and then the oscilloscope will start to execute the self-

calibration program.

- After starting the self-calibration program, click you can or tap Exit to cancel

self-calibration operation at any time.

3. After completing the self-calibration, restart the oscilloscope. In the Horizontal

system menu, select "Average" for the Acquisition menu. Then click or tap the

input field for the Averages menu item to set it by using the pop-up numeric

keypad. Set the number of averages to 16.

4. Set the vertical scale of each channel to 2 mV/div and view the offset of the

waveform of each channel. If the offset is greater than 0.5 div, check whether there

are interference signals around you and whether the power source is well

grounded. If yes, perform self-calibration again.

5. Click or tap Close to close the self-calibration information window.

4.2

Test Result Record

Record and keep the test result of each test. In the last chapter of this manual, a test
result record form is provided. The form lists all the test items and their
corresponding performance limits as well as spaces for users to record the test
results.

TIP

It is recommended that users photocopy the test record form before each test and record the
test results in the copy so that the form can be used repeatedly.

 Overview

Copyright ©RIGOL TECHNOLOGIES CO., LTD. All rights reserved.

DS70000 Performance Verification

9

Содержание DS70000 Series












































Отзывы:

Нет отзывов