Rigol DL3000 Series Скачать руководство пользователя страница 158

Страница: 158 / 163

RIGOL

Chapter 4 Troubleshooting

4-2

DL3000 User’s Guide

(4)

If the problem still persists, contact

RIGOL

An exception occurs to the input in CR mode.

(1)

Check whether the output of the DUT is normal, e.g. check whether an

oscillation occurs to the DUT.

(2)

Check whether the range for the resistance is properly set.

(3)

If the problem still persists, contact

RIGOL

An exception occurs to the input in CP mode.

(1)

Check whether the cable that connects the instrument to the DUT is

reversely connected, which causes the instrument to report the alarm for

reverse connection.

(2)

Check whether the output of the DUT is normal, e.g. check whether an

oscillation occurs to the power supply; whether the rated power of the

power supply fails to reach the set power of the load.

(3)

If the problem still persists, contact

RIGOL

An exception occurs to the transient feature test in CC mode.

(1)

Check whether the cable that connects the instrument to the DUT is

reversely connected, which causes the instrument to report the alarm for

reverse connection.

(2)

Make a real-time measurement for the CC slew rate. If the value failed to

reach the standard, shorten the leads between the DUT and the instrument

as much as possible, because the long leads will result in a slow slew rate.

(3)

Check whether the range of the load current is properly set.

(4)

If the problem still persists, contact

RIGOL

The USB storage device cannot be recognized.

(1)

Check whether the USB storage device can work normally.

(2)

Make sure the USB storage device used is FAT32-format Flash storage type,

as this instrument does not support hardware storage type USB storage

device.

(3)

Restart the instrument and insert the USB storage device to check it.

(4)

If the USB storage device still cannot work normally, please contact

RIGOL

Содержание DL3000 Series




































































































































































Результаты поиска

Содержание DL3000 Series

Отзывы:

Похожие инструкции для DL3000 Series

Бренды по названию

Популярные бренды

Rigol DL3000 Series, Руководство пользователя

Результаты поиска

Содержание DL3000 Series

Отзывы:

Похожие инструкции для DL3000 Series

Бренды по названию

Популярные бренды