background image

5

GENERAL

The boiler is delivered in separate crates. Check 
that it is complete, undamaged and as ordered as 
soon as you receive it. Report any discrepancies or 
damage to the dealer who sold it.

The

 

RTQ 3S 

boiler must be installed by a 

legally qualified heating engineer. On completion 
of the installation, the installer must issue the owner 
with a declaration of conformity confirming that the 
installation has been completed to the highest stan-
dards in compliance with the instructions provided 
by 

r

 in this instruction manual, and that it con-

forms to all applicable laws and standards.

The boiler must only be used for the purpose spe-
cified by 

r

 and for which it is designed. The 

manufacturer declines all responsibility, contractual 
or other, for damage to property or injury to per-
sons or animals caused by improper installation, 
adjustment, maintenance or use.

If you notice any water leaking from the boiler, 
disconnect it immediately from the mains electricity 
supply, shut off the water supply, and notify your 
local 

r

 Technical Assistance Centre or a quali-

fied heating engineer immediately.

Periodically check that operating pressure in the 
water circuit is 

over 1 bar

 but below the maximum 

limit specified for the boiler. If this is not the case, 
contact 

r

’s Technical Assistance Service or a 

professionally qualified heating engineer.

If the boiler is not going to be used for an extended 
period of time, contact 

r

’s Technical Assistance 

Service or a qualified heating engineer to have it 
prepared for shut-down as follows:

- Switch the boiler OFF at the control panel and at the 

mains power switch

- Close the fuel cock and heating circuit water cock
- Drain the central heating circuit if there is any risk of 

freezing.

Drain the central heating circuit if there is any risk of 
freezing

This instruction manual is an integral part of the boi-
ler. It must be kept safe and must ALWAYS accom-
pany the boiler, even if it is sold to another owner or 
transferred to another user or to another installation.

 

If you damage or lose this manual, order a repla-
cement immediately from your local 

r

 Technical 

Assistance Centre.

Do not allow children or infirm persons to operate 
this

 

RTQ 3S 

boiler unsupervised.

Do not operate any electrical devices or equipment, 
including switches or domestic appliances, etc., if 
you can smell fuel or fumes. If you detect any suspi-
cious smells:

-  Ventilate the room by opening all doors and win-

dows.

-  Close the fuel shut-off cock.
-  Report the fault immediately to the 

r

 Technical 

Assistance Service or a professionally qualified 
heating engineer.

Do not touch the boiler while barefoot or wet.

Never clean or service the boiler without first 
disconnecting it from the mains electricity supply 
by turning the main power switch and the control 
panel switch OFF.

Do not tamper with or adjust the safety or control 
devices without prior authorisation and instruc-
tions from the boiler’s manufacturer.

Never pull, disconnect, or twist the electrical 
cables coming from the boiler even if it is discon-
nected from the mains electricity supply.

Do not obstruct or restrict the vents in the room 
where the boiler is installed. Adequate ventilation 
is essential for correct combustion.

Do not expose the boiler to the elements. Do not 
install the boiler outdoors. It is not designed to 
work outdoors and is not fitted with the necessary 
automatic anti-frost systems to do so.

Do not switch the boiler off if outdoor temperature 
drops below ZERO (risk of freezing).

Do not store containers of flammable substances 
in the room where the boiler is installed.

Do not dispose of packaging material into the 
environment, or leave it within the reach of 
children, since it can become a potential hazard. 
Dispose of packaging material in compliance 
with applicable legislation.

The operation of any appliance that uses fuel, electrical power and water demands that a number of fundamental safety 
precautions be respected.

General safety information

GENERAL SAFETY INFORMATION  

Precautions

PRECAUTIONS 

  

GENERAL

Содержание RTQ 1100 3S













































Отзывы: