Riello UPS Sentryum S3M Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

Riello UPS Sentryum S3M Скачать руководство пользователя страница 30

- ACTIVE series -

- 28 -

S3M

-

S

INGLE PHASE VERSION

The first wire to be connected is the protective earth wire, which is to be inserted in the terminal marked PE.
During operation the UPS must be connected to the earthing system.

Connect the input and output cables to the terminal blocks as indicated in the figure below:

TERMINAL BLOCK COLOURS

RED

BLACK

GREY

BEIGE

BLUE

External battery positive

External battery negative

Input & Bypass Phases

Output Phases

Input, Output and external

battery Neutral

THE INPUT AND BYPASS NEUTRALS MUST ALWAYS BE CONNECTED.

Jumpers (for more details about their installation or removal, refer to "APPENDIX")

To connect a single-phase source to the input: fit the supplied jumper to link the three input terminal blocks, as shown in the image
above. The jumper is supplied within the accessories box. Then connect the phase cable to the L1 terminal block.

D

UAL

I

NPUT VERSION

THE INPUT AND BYPASS LINES MUST BE REFERENCED TO THE SAME NEUTRAL POTENTIAL.

Note:

connection to the BATTERY terminal blocks is only required if an

(optional)

Battery Cabinet is present.

Jumpers:

For more information regarding all possible configurations, refer to

Table 23

.

«
...
28
29
30
31
32
...
»

Содержание Sentryum S3M













































Отзывы:

Нет отзывов