RIDGID WTS2000L Скачать руководство пользователя страница 36

Страница: 36 / 44

Item

Part Name

QuaNtIty

Nut Wrench

Hex Wrench

ATTACHMENTS

TROUBLESHOOTING

WARNING:
For your own protection, turn the ON/OFF switch to “OFF,” and always remove the plug from power-source outlet
before troubleshooting.

TROUBLE

PROBABLE CAUSE

SOLUTION

Motor stops running

There is no power to the electrical outlet.

Make sure that the outlet has power.

Low voltage.

Check that the power source voltage is 10V.

Plugs aren’t fully connected to the power
source.

Verify that the plugs are securely connected.

Switch isn’t “ON.”

Lift the ON/OFF switch to turn the saw on.

The carbon brushes have worn out
completely.

Replace the carbon brushes.

GFCI is tripped.

Press the ON/OFF switch down to turn the
saw off; reset the button on the GFCI.

Overload protector tripped.

Press the overload-protector switch to restart
the saw.

The water pump cannot
inject water

The water-pump plug is not firmly connected
to the saw receptacle.

Connect the water-pump plug to the saw
receptacle.

There is not enough water in the water tray.

Make sure that the water-pump intake is fully
immersed in water.

The water hose is loose or off.

Reconnect the water hose to the pump.

The water valve is in “OFF” position.

Turn the valve to the “ON” position.

The water hose or water nozzle is jammed.

Clean the water hose or water nozzle, or
replace them.

The water pump filter is too dirty.

Clean the water-pump filter.

The water pump is damaged.

Replace the water pump.

LED Lights/Laser Beam
projection is hard to see

Light in work area is too bright.

Move the machine to a work area where the
light isn’t as bright.

Dust or water is on the laser-aperture cover or
on the surface of LED lights.

Wipe the dust or water off with a clean, soft
cloth.

LED Lights/Laser beam
projection doesn’t work

The LED Lights /LASER switch isn’t turned
on.

Turn on the LED/LASER switch.

Frequent tripping of
overload protector

Rapid feeding of material into the cutting
blade

Feed the material more slowly into the
cutting blade

Low voltage and heavy load

When cutting extremely dense materials,
make sure that power supply voltage is
exactly 10 V

Содержание WTS2000L













































Результаты поиска

Содержание WTS2000L

Отзывы:

Похожие инструкции для WTS2000L

Бренды по названию

Популярные бренды

RIDGID WTS2000L, Руководство оператора

Результаты поиска

Содержание WTS2000L

Отзывы:

Похожие инструкции для WTS2000L

Бренды по названию

Популярные бренды