RIDGID R4231 Скачать руководство пользователя страница 22

Страница: 22 / 36

OPERATION

See Figures 23 and 24.
ALWAYS adjust and secure fence position to avoid contact

with the blade.
DO NOT start the Miter Saw without checking for interference

between the Blade and the Sliding Fence.
ALWAYS

recheck for such interference when changing

miter or bevel angles.

• DO NOT allow familiarity with tools to make you careless

Remember that a careless fraction of a second is sufficient to

inflict serious personal injury

• ALWAYS wear eye protection with side shields and marked to comply with ANSI Z87

1 Failure to do so could result in objects

being thrown into your eyes, resulting in possible serious personal injury

• DO NOT use any attachments or accessories not recommended by the manufacturer of this tool

The use of attachments or

accessories not recommended can result in serious personal injury

• Before starting any cutting operation, clamp or bolt the compound miter saw to a workbench

NEVER operate the miter saw on

the floor or in a crouched position

Failure to heed this warning can result in serious personal injury

• To avoid serious personal injury, ALWAYS tighten the miter lock knob and bevel lock handle securely before making a cut

Failure to do so could result in serious injury due to movement of the control arm or miter table while making a cut

• To avoid serious personal injury, KEEP hands outside the no hands zone, at least 4 inch from blade

NEVER perform any cutting

operation freehand (without holding workpiece securely against the fence)

The blade could grab the workpiece if it slips or

twists

• When using a work clamp or C-clamp to secure the workpiece, clamp workpiece on one side of the blade only

The workpiece

MUST remain free on one side of the blade to prevent the blade from binding in workpiece

The workpiece binding the blade will

cause motor stalling and kickback

This situation could cause an accident resulting in serious personal injury

• NEVER move the workpiece or make adjustment to any cutting angle while the saw is running and the blade is rotating

Any slip

can result in contact with the blade causing serious personal injury

• When cutting, DO NOT force the blade against the workpiece

Forcing the blade will cause a drop in motor RPM and increase

the risk of overheating the saw blade tips

You may use this tool for the following purposes:
• Bevel cutting and compound cutting for crown moldings,

etc

• Cross cutting wood.
• Cross cutting for moldings, door casings, picture frames,

etc

• This saw is for cutting wood/wood-like products. The blade

provided is acceptable for wood/wood-like products cutting

ONLY.

Figure 24

Figure 23

Содержание R4231





































Результаты поиска

Содержание R4231

Отзывы:

Бренды по названию

Популярные бренды

RIDGID R4231, Руководство оператора

Результаты поиска

Содержание R4231

Отзывы:

Бренды по названию

Популярные бренды