Ricoh SP 6430DN Скачать руководство пользователя

Страница: 67 / 124

Message

Cause

Solution

"USB has a problem. Please call
service."

The printer has detected a
USB board failure.

Turn the printer off, and then
turn it on again. If the problem
persists, contact your sales or
service representative.

"Values set for IPv6/Gateway
addresses are invalid.(110/210)"

The IPv6 address or gateway
address is invalid.

Check the network settings.

"WPA Auth. incomplete.(211)"

WPA authentication could not
be completed.

Contact your network
administrator.

Alert Messages (Printed on Error Logs and Reports)

This section describes likely causes of and possible solutions for the error messages that are printed on
the error logs or reports.

Message

Cause

Solution

"84: Error"

There is no work area available
for image processing.

Select [Font Priority] for
[Memory Usage] in [System].
Decrease the number of files
sent to the printer.

"85: Error"

The specified graphics library is
unavailable.

Check that the data is valid.

"86: Error"

Parameters of the control code
are invalid.

Check the print settings.

"91: Error"

Printing was canceled by the
auto job cancel function due to
a command error.

Check that the data is valid.

"92: Error"

Printing was canceled because
the [Job Reset] key or the
[Suspend/Resume] key was
pressed on the printer's control
panel.

Perform the print operation
again as necessary.

When Messages Are Displayed

Содержание SP 6430DN





























































































































Результаты поиска

Содержание SP 6430DN

Отзывы:

Похожие инструкции для SP 6430DN

Бренды по названию

Популярные бренды

Ricoh SP 6430DN, Руководство пользователя

Результаты поиска

Содержание SP 6430DN

Отзывы:

Похожие инструкции для SP 6430DN

Бренды по названию

Популярные бренды