Ricoh FT2012+ Скачать руководство пользователя

Страница: 80 / 88

USE AND STORAGE OF SUPPLIES

Copy Paper

❐

Copy paper of the types or in the conditions listed below are not recom-
mended for this copier.

✒

Folded, curled, creased, or damaged paper

✒

Torn paper

✒

Damp paper

✒

Perforated paper

✒

Paper with conductive or low electrical resistance such as carbon or

sliver coated paper.

✒

Wavy paper

✒

Thermal paper, art paper

✒

Thin paper that has low stiffness

❐

Adhesive labels should be fed from the bypass feed entrance one sheet at a
time.

❐

Translucent paper should be fed from the bypass feed entrance.

❐

Translucent paper should be fed so that the paper grain is oriented with the
paper path.

❐

Do not touch copy paper if your fingers are wet or oily; finger prints may
appear on the copy.

INT

INING Y

UR COP

DO’

ND DON’T

USE AND STORAGE OF SUPPLIES

Содержание FT2012+

























































































Результаты поиска

Содержание FT2012+

Отзывы:

Похожие инструкции для FT2012+

Бренды по названию

Популярные бренды

Ricoh FT2012+, Руководство по эксплуатации

Результаты поиска

Содержание FT2012+

Отзывы:

Похожие инструкции для FT2012+

Бренды по названию

Популярные бренды