Ricoh B245-62 Скачать руководство пользователя страница 29

Страница: 29 / 138

Ricoh Co. Ltd.

http://www.ricoh.com/

B245-62 / PD-C4

Slide 29

Image Processing – Overview

The illustration shows image processing data flow.

See the notes for a list of the processes done.

Note: The next 13 slides will cover some details of image processing.

The BICU is where the main image processing is done.

The image data from the SBU goes to the IPU (Image Processing Unit) on the BICU
board, which carries out the following processes on the image data:

Auto shading

White/black line correction

ADS

Scanner gamma correction

Magnification (main scan)

Filtering (MTF and smoothing)

ID gamma correction

Binary picture processing

Error diffusion

Dithering

Video path control

Test pattern generation

The image data then goes to the GDI controller.

Note: The IPU and VCU are contained in the same IC (called SCRATCH) on the BICU.

For more information about image processing, refer to the core technology manual.

Содержание B245-62











































































































































Результаты поиска

Содержание B245-62

Отзывы:

Похожие инструкции для B245-62

Бренды по названию

Популярные бренды

Ricoh B245-62, Обучение по обслуживанию

Результаты поиска

Содержание B245-62

Отзывы:

Похожие инструкции для B245-62

Бренды по названию

Популярные бренды