manualshive.com logo in svg

Ricoh Aficio Color 4006, Руководство по обслуживанию

Поделиться
Скачать
Ricoh Aficio Color 4006 Скачать руководство пользователя страница 371

SP TABLE

24 February, 1999

2

SP No.

Item

[Display]

Default

Value

Value Range

Step

SP7-

902/3

Description

1-101: Oil End Sensor [Oil End Sensor]
1-101-000

[Fuser Oil End Check]

1

0 = Not used
1 = Used

1

Yes

Specifies whether the oil end sensor is used.

01-104:
01-104-00

Fusing control method selection
[Fusing Control]

1

0: Phase control

1: On/off control

1

Yes

Selects the fusing temperature control mode.
On/off control minimizes the radio noise generated
when the fusing lamp is turned on.
Phase control should only be selected if a user has
problems with electrical noise or interference, such
as a flickering fluorescent lamp or main power supply
voltage drops.
The main switch needs to be turned off and on when
the setting is changed.
0 = Phase control
1 = ON/OFF control.

01-105: Hot/pressure roller temperature settings [Roller.Tmp Set]
01-105-01

Hot roller, 1st side, Idling
[Hot Rllr/ Idling]

163 °C

100 to 200 °C

1

Yes

Sets the temperature at which idling starts.
Idling starts for 2 minutes when the temperature
becomes over the target - 15 

°

C.

If the temperature is higher than 50 

°

C when the

power relay turns on, idling is not executed.

Содержание Aficio Color 4006








































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды