manualshive.com logo in svg

Ricoh Aficio Color 4006, Руководство по обслуживанию

Поделиться
Скачать
Ricoh Aficio Color 4006 Скачать руководство пользователя страница 112

24 February, 1999

LASER EXPOSURE

2-63

Detailed

Descriptions

Auto Power Control (APC)

Even if a constant electric current is applied to the laser diode, the intensity of the
output light changes with the temperature. The intensity of the output decreases as
the temperature increases.

In order to keep the output level constant, the output light intensity is monitored
through a photodiode (PD) enclosed in the laser diode. The photodiode passes an
electrical current that is proportional to the light intensity. The output is not affected
by temperature, so it faithfully reflects the changes in the LD output, without adding
anything itself.

Just after the main switch is turned on, the current control IC on the LD drive board
excites the laser diode at full power (power level 32) and stores the output of the
photodiode as a reference. The current control IC monitors the current passing
through the photodiode. Then it increases or decreases the current to the laser
diode as necessary, comparing it with the reference level. Such auto power control
is done during printing while the laser diode is active.

The laser power level is adjusted on the production line. Do NOT touch the variable
resistors on the LD unit in the field.

Current

Control

IC

L D 5 V

L D

P D

LD Drive Board

V I D E O

L E V E L

L D   O F F

A259D501.WMF

Содержание Aficio Color 4006








































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды