fe80:0:0:0207:40ff:0:340e
4. Sections where only zeros exist can be abbreviated with double colons (::). This abbreviation can be
done also where succeeding sections contain only zeros (but this can be done only at one point in
the address). The example in "2" and "3" above then becomes:
fe80::207:40ff:0:340e (only the first null sets zero digits are abbreviated as "::")
-or-
fe80:0:0:0:207:40ff::340e (only the last null set before "340e" is abbreviated as "::")
5832
HDD Init.
Format HDD
Press [#Enter] to initialize the HDD. After formatting is complete, turn the machine power off/
on.
5840
IEEE 802.11b
006
Channel Max
Sets the maximum range of the bandwidth for the wireless LAN. This bandwidth setting varies
for different countries.
[1~14/1]
007
Channel Min
Sets the minimum range of the bandwidth for operation of the wireless LAN. This bandwidth
setting varies for different countries.
[1~14/1]
011
WEP key number
Determines how the initiator (SBP-2) handles subsequent login requests.
[0~1/1]
0:If the initiator receives another login request while logging in, the request is refused.
1:If the initiator receives another login request while logging in, the request is refused and the
initiator logs out.
Note: Displayed only when the wireless LAN card is installed.
5842
NFA Analysis
Net File Application Analysis
001
Setting 1
This is a debugging tool. It sets the debugging output
mode of each Net File process.
Bit
Groups
Service Program Mode Tables
225
5
Содержание A-P4
